[Are Lynx MK2 original screens still available]

Is it still possible to obtain the original MK2 Lynx LCD screen? maybe Best electronics?

 

I know there are LCD replacement screens out there but i was looking for an original part

[Falcon TOS 4.04 rom image needed]

Well i've been trying to make this TOS 4.04 Eprom with no success, i'm using Hitachi erasable HN27C4096CC-12 EPROMs

 

Using a Willem PCB50 programmer

 

I load the file (512K) (Downloaded from this thread) into the Willen PCB50

 

I can see the first word starts 602e

 

The EPROM is blank, the programmer copies and verifies the image

 

I insert the EPROM into the Falcon and all i get on a low res colour monitor is a black screen with red lines, no boot

 

Re install the original rom and all is well so there's nothing up with the Falcon

 

Can anyone help?

 

 

[Falcon Gal / Pal ic images needed please]

OK 

 

So i see from these files that there are 2 x U44 files (U44.LCR and U44.JED)

 

So which file do i use? and how do i get them onto the IC? obviously i have an eprom programmer

 

I just want to make sure i program the chip correctly as don't want to damage the Falcon!

[Mega STE / TT rear Serial port panel block needed]

Yes i know i could make something but ultimately i'd like the original part :0)

[Mega STE / TT rear Serial port panel block needed]

I'm after one of the small blocks used to mount the Serial port on the rear of the Mega STE / TT (see  pic) 

 

If anyone can help let me know

 

thanks 

[Falcon TOS 4.04 rom image needed]

Can i use HN27C4096CC-10

 

or does the rom need to be a -12 or -15 ?

 

Thanks

[Falcon TOS 4.04 rom image needed]

Thanks

 

So do i need to do anything to this image or can i simply burn that file onto a rom?

[Falcon TOS 4.04 rom image needed]

Can anyone point me in the right direction of a working Falcon TOS 4.04 rom image please so i can burn my own TOS rom

 

Thanks

[Atari STM1 mouse problem]

OK so i used a phone camera to check the LEDs on an STM1 i have that doesn't move left/right

 

And sure enough i can see all 4 LEDS emitting a purple coloured light

 

So does this mean the LEDS are ok? and there is something else causing the lack of left/right movement?

 

On this particular mouse i have changed the cable and caps and still the issue, no broken solders or tracks

 

What else to look at apart from changing the chip and testing resistors?!

[Falcon Gal / Pal ic images needed please]

Thanks for this

 

Is it also possible to save the data on a working Gal/Pal into the rom burner and then burn back the data to a new chip? 

[Falcon Gal / Pal ic images needed please]

These chips - U62, U63, U67, U68 Chips C30283(0/1/2/3)-001 PAl/GAL/IC

And the longer U44 chip

[Falcon Gal / Pal ic images needed please]

Does anyone know where i could find the gal / pal images for the 5 small chips on the Falcon?

[Atari STM1 mouse problem]

How do you use a cell phone to test the wheel emitter?

[Falcon CPU - Which pins are Data and Address?]

I have a logic probe. Ok so i will check as you say around A3 area...

 

Thanks for your help 

[Falcon CPU - Which pins are Data and Address?]

I'm just going on what is stated in the Falcon service manual for testing CPU, "check data and address lines to see if they are toggling" it says when test cartridge fitted on initial power up

 

The manual doesn't specify which data and address lines to check so do i assume any of them??!!

[Falcon CPU - Which pins are Data and Address?]

OK so there isn't 1 x data line or address line but many data and address lines!

[Falcon CPU - Which pins are Data and Address?]

I have the PDF of the Falcon CPU with pinout of the pins but none are marked as Data or Address

 

How do i find out these 2 lines?

 

Thanks 

68030 QFP.pdf

[Scope for Falcon diagnostics, can anyone recommend one?]

Can a logic probe be used for checking CPU clocks and Halt lines?

 

I'm ultimately new to this so want something simple to understand and use

[Scope for Falcon diagnostics, can anyone recommend one?]

Thanks for your replies

 

Ultimately i just want the scope for Atari ST / Falcon repairs

 

Checking clock signals to and from chips and Halt lines as per the Atari service manuals

 

Would this Pico scope be ok for this?

[Scope for Falcon diagnostics, can anyone recommend one?]

Can anyone recommend a scope for fault finding a dead Falcon? ultimately one of these small LCD types would be good as found on ebay

 

Any help appreciated thanks 

[Need pictures of SC 1224 colour monitor PSU cable connectors please]

Any chance you could let me know the part number of the main PCB on your USA model please?

 

The number is located front bottom corner. Opposite side to the rotary swtches

 

My UK part number is P/N 111 - 704A

 

Thanks

[Need pictures of SC 1224 colour monitor PSU cable connectors please]

Thankyou so much! i think that's all my picture requests now

 

I will test it soon.........

[Need pictures of SC 1224 colour monitor PSU cable connectors please]

If it is possible i wouldn't mind seeing there 2 x orange wires on the back of the rotary power switch :0)

[Need pictures of SC 1224 colour monitor PSU cable connectors please]

Thanks so much, this is really helpful

 

Could you also confirm regarding the red and blue wire that plugs into the PSU at the far end (mains in)  

 

Which colour goes to live and neutral on the 3 pin input plug on the back of the monitor

 

And that's all! thanks :0)

[USA SC 1224 PSU in UK SC 1224 monitor - how to mod?]

This seems to be how USA PSU's work as i have also a 117V USA Falcon PSU and that is wired the same with just the live wire across the switch which has 2 x terminals (compared the the UK 4 x terminals) and the neutral wire goes straight to the PSU, capacitors across the power port