So, a few weeks back I bought a 800 after hearing about the FujiNet. Finally got it yesterday and nothing but issues so far, starting to wonder if it is defective. Most of the time I'll try to boot it and will get nothing, occasionally I'll hear the SIO beeping then it will stop and it will just sit there, other times I'll get a BOOT ERROR, or it will just go to the READY prompt. A few times it actually did boot to the config screen. But if I reboot the computer after that it will not work again. Tried flashing it thinking that would help but nope.
This is the output from when it just booted to the READY prompt. Is the CHECKSUM_ERROR an indicator of an issue? Anything else I can try? thx
Using '/dev/cu.usbserial-10' as serial port.
Showing logs:
[11:08:14]
[11:08:14]3153 00 00
[11:08:14]CF: 00 CHECM_ERR
[11:08:14]udratfm1920to 67431
Serial port closed!
[11:08:14]rate chrom1
Serial port closed!
[11:08:14]
[11:08:14]CF: 38 c0 f8 c0 38
[11:08:14]CHECKSUM_ERROR
[11:08:14]
[11:08:14]CF: 38 c0 f8 c0 38
[11:08:14]CHECKSUM_ERROR
[11:08:14]Toggling baudrate from 67431 to 19200
[11:08:14]set_baudrate change from 67432 to 19200
[11:08:14]
[11:08:14]CF: 31 53 00 00 84
[11:08:14]FujiNet CONFIG boot
[11:08:14]disk sio_process()
[11:08:14]ACK!
[11:08:14]disk STATUS
[11:08:14]response: 0x00, 0xff, 0xfe
[11:08:14]->SIO write 4 bytes
[11:08:14]COMPLETE!
[11:08:14]
[11:08:14]CF: 00 00 00 31 53
[11:08:14]CHECKSUM_ERROR
[11:08:14]
[11:08:14]CF: 31 53 00 00 84
[11:08:14]FujiNet CONFIG boot
[11:08:14]disk sio_process()
[11:08:14]ACK!
[11:08:14]disk STATUS
[11:08:14]response: 0x00, 0xff, 0xfe
[11:08:14]->SIO write 4 bytes
[11:08:14]COMPLETE!
[11:08:14]
[11:08:14]CF: 00 00 00 31 53
[11:08:14]CHECKSUM_ERROR
[11:08:14]Toggling baudrate from 19200 to 67431
[11:08:14]set_baudrate change from 19200 to 67431
[11:08:14]
[11:08:14]CF: 38 c0 f8 c0 38
[11:08:14]CHECKSUM_ERROR
[11:08:14]
[11:08:14]CF: 38 c0 f8 c0 38
[11:08:14]CHECKSUM_ERROR
[11:08:14]Toggling baudrate from 67431 to 19200
[11:08:14]set_baudrate change from 67432 to 19200
[11:08:14]
[11:08:14]CF: 31 53 00 00 84
[11:08:14]FujiNet CONFIG boot
[11:08:14]disk sio_process()
[11:08:14]ACK!
[11:08:14]disk STATUS
[11:08:14]response: 0x00, 0xff, 0xfe
[11:08:14]->SIO write 4 bytes
[11:08:14]COMPLETE!
[11:08:14]
[11:08:14]CF: 00 00 00 31 53
[11:08:14]CHECKSUM_ERROR
[11:08:14]
[11:08:14]CF: 31 53 00 00 84
[11:08:14]FujiNet CONFIG boot
[11:08:14]disk sio_process()
[11:08:14]ACK!
[11:08:14]disk STATUS
[11:08:14]response: 0x00, 0xff, 0xfe
[11:08:14]->SIO write 4 bytes
[11:08:14]COMPLETE!
[11:08:14]
[11:08:14]CF: 00 00 00 31 53
[11:08:14]CHECKSUM_ERROR
[11:08:14]Toggling baudrate from 19200 to 67431
[11:08:14]set_baudrate change from 19200 to 67431
[11:08:14]
[11:08:14]CF: 38 c0 f8 c0 38
[11:08:14]CHECKSUM_ERROR
[11:08:14]
[11:08:14]CF: 38 c0 f8 c0 38
[11:08:14]CHECKSUM_ERROR
[11:08:14]Toggling baudrate from 67431 to 19200
[11:08:14]set_baudrate change from 67432 to 19200
[11:08:15]
[11:08:15]CF: 31 53 00 00 84
[11:08:15]FujiNet CONFIG boot
[11:08:15]disk sio_process()
[11:08:15]ACK!
[11:08:15]disk STATUS
[11:08:15]response: 0x00, 0xff, 0xfe
[11:08:15]->SIO write 4 bytes
[11:08:15]COMPLETE!
[11:08:15]
[11:08:15]CF: 00 00 00 31 53
[11:08:15]CHECKSUM_ERROR
[11:08:15]
[11:08:15]CF: 31 53 00 00 84
[11:08:15]FujiNet CONFIG boot
[11:08:15]disk sio_process()
[11:08:15]ACK!
[11:08:15]disk STATUS
[11:08:15]response: 0x00, 0xff, 0xfe
[11:08:15]->SIO write 4 bytes
[11:08:15]COMPLETE!