Search the Community
Showing results for tags 'Grips03'.
-
Custom made Atari 5200 digital arcade controller - $185 Supports rapid fire on button C and D. Rapid fire has been tuned for Defender and Moon Patrol. Upgraded with the following new parts: Custom designed and professionally printed Atari 5200 digital arcade controller PCB Seimitsu bearing and spring receiver Shin Etsu joystick grease Seimitsu ball top - black (4) Panasonic 2N microswitches .110/.187 Sanwa quick connects Sanwa hard quick covers (4) Seimitsu screw in buttons (black) - these are much higher quality than the stock buttons. Buttons B and C are shaved on the sides to fit flat in the case ~5.5 foot long db15 cable that plugs directly into Atari 5200 console - very high quality cable Reset button Built in keypad Custom made Atari 5200 sticker in top right corner. (4) .75 rubber feet. Used parts: Like new - NeoGeoX controller case and joystick or NeoGeo AES controller imported from Japan. Used controllers are in good shape, but do have light scratches on them. There tend to be more scratches on the bottom, than the top. Controllers are hand washed and very clean. Button mapping: A button = Primary action button B button = Secondary action button C button = Primary action button with rapid fire D button = Secondary action button with rapid fire Select button = Pause Start button = Start Reset button - near where the db15 cables exits controller Controller comes with 8 way joystick gate. Which is great for games like Defender, Moon Patrol, MULE. I also sell 4-way joystick gate which can be used for games like Ms. Pac-Man. Supports all games that support digital controls (this is most of the 5200 games), however there are a couple analog only games that no digital controller supports. Which Joystick Gate is best? 2-way games are fine with either 4 or 8 way gate. 4-way games with 8-way gate are not good. 4-way games with 4-way gate are great 8-way games with 4-way gate are horrible 8-way games with 8-way gate are great Custom made Colecovision arcade controller - $185 Supports Colecovision keypad and 4 action buttons (like Coleco's Super Action Controller). Controller also works on Commodore 64 and Atari 2600 supporting a single fire button. Upgraded with the following new parts: Custom designed and professionally printed Colecovision arcade controller PCB. Seimitsu bearing and spring receiver Shin Etsu joystick grease Seimitsu ball top (4) Panasonic 1N microswitches .110/.187 Sanwa quick connects Sanwa hard quick covers (4) Seimitsu screw in buttons - these are much higher quality than the stock buttons. Buttons B and C are shaved on the sides to fit flat in the case ~5.5 foot db9 cord Super Cable - this is a very high quality db9 cord. Built in keypad Custom Colecovsion arcade controller sticker in top right. (4) .75 rubber feet. Used Parts (in good shape): Like new - NeoGeoX controller case and joystick or NeoGeo AES controller imported from Japan. Used controllers are in good shape, but do have light scratches on them. There tend to be more light scratches on the bottom, than the top. Controllers are hand washed and very clean. Button mappings: Button A = Left action button Button B = Right action button Button C = 3rd action button Button D = 4th action button Select button = Keypad 1 Start Button = Keypad * Comes with 8-way joystick gate. Good for shooter games like Star Force and Sky Jaguar. 4-way gate can be purchased separately for games like Pac-Man Collection, Donkey Kong, etc. Which Joystick Gate is best? 2-way games are fine with either 4 or 8 way gate. 4-way games with 8-way gate are not good. 4-way games with 4-way gate are great 8-way games with 4-way gate are horrible 8-way games with 8-way gate are great Custom made Sears Super Video Arcade / Intellivision 2 arcade controller. $220 Joystick supports true 8-way operation. Supports 4-way operation with separately sold 4-way joystick gate Upgraded with the following new parts: Custom designed and professionally printed Intellivision arcade controller PCB Seimitsu bearing and spring receiver Shin Etsu joystick grease Seimitsu ball top (4) Panasonic 1N microswitches .110/.187 Sanwa quick connects for all joystick and button microswitches. Buttons C&D have solder and heat-shrink due to space constraints. Sanwa hard quick connect covers (4) Seimitsu screw in buttons (button color is Black) - these are much higher quality than the stock buttons. Buttons B and C are shaved on the sides to fit flat in the case Keypad (4) .75 rubber feet Single AA battery holder on right hand side, single AA battery will last for several months under constant use, under heavy use you would change ~ twice per year. Battery is reverse polarity protected and fused. Power switch installed in the rear of controller. Custom made battery sticker on bottom - showing proper battery direction Custom made no screw sticker on bottom Custom made Intv2 Controller sticker on top right. ~5.5 foot db9 cable Used Parts: Like new - NeoGeoX controller case and joystick or NeoGeo AES controller imported from Japan. Used controllers are in good shape, but do have light scratches on them. There tend to be more light scratches on the bottom, than the top. Controllers are hand washed and very clean. Button mapping: Button A = Top Left and Right button Button B = Bottom Left Button C = Bottom Right Button D = Top Left and Right button Keypad * = Keypad Clear Keypad # = Keypad Enter Select button = Pause for most games, think of it as a shortcut to pressing keypad 3+7 or 1+9. Start button = Keypad Enter Which Joystick Gate is best? 2-way games are fine with either 4 or 8 way gate. 4-way games with 8-way gate are not good. 4-way games with 4-way gate are great 8-way games with 4-way gate are horrible 8-way games with 8-way gate are great Examples: 2-way games: Astrosmash, Space Armada, Space Patrol 4-way games: Boulder Dash, D2K, DK Arcade, Christmas Carol, Thunder Castle, Burgertime, Lock N Chase, Dig Dug, Frogger, Ms. Night Stalker, Ms. Pac-Man, Beauty and Beast, Super Chef BT, Piggy Bank 8-way games: River Raid, Match 5, Dreadnaught Factor, Commando, Mission X, Nova Blast, Empire Strikes Back, Atlantis Custom made Vectrex digital arcade controller - $115 Supports all the Vectrex games that support digital controls - this is most of them. Scramble,Vector Pilot, and Mindstorm work awesome with this controller!!!! Upgraded with the following new parts: Custom designed and professionally printed Vectrex digital arcade controller PCB Seimitsu bearing and spring receiver Shin Etsu joystick grease Seimitsu ball top (4) Panasonic 1N microswitches internal wiring (soldered with heat shrink tubing) (4) Seimitsu screw in buttons - these are much higher quality than the stock buttons. Buttons B and C are shaved on the sides to fit flat in the case (4) .75 rubber feet. 6 foot Wico heavy duty db9 cable - cut to fit Vectrex opening Used Parts: Like new - NeoGeoX controller case and joystick Vectrex button mapping: Button A = Vectrex button 1 Button B = Vectrex button 2 Button C = Vectrex button 3 Button D = Vectrex button 4 Controller comes with 8-way joystick gate for games like Vector Pilot, Minestorm and Scramble. I also sell a 4-way gate for games like Clean Sweep. Which Joystick Gate is best? 2-way games are fine with either 4 or 8 way gate. 4-way games with 8-way gate are not good. 4-way games with 4-way gate are great 8-way games with 4-way gate are horrible 8-way games with 8-way gate are great Directions to change the Joystick Gate: 1) Remove 4 rubber feet. 2) Remove 4 screws to open case. 3) Remove 8 screws to remove gate 4) Put on new gate, make sure little posts on the gate fit into holes in the microswitches - gate, microswtches should all be level. Re-install the same 8 screws from step 3 5) Turn case to look at back of it. Put top and bottom of case together. Do not use the screws to force the top and bottom together. Re-install the 4 screws from step 2. 6) Put rubber feet back on step 1 Do not change gate often as screw holes are plastic, not metal threaded, hence can wear out. If you do change, make sure to not over-tighten them When re-installing the screws It helps to put screw in place and turn to loosen, this helps the screw find the old groove vs. making new ones. If screw is hard to turn back-out and repeat this process. Send PM if interested. grips03 Sample pictures below:
-
From the album: Hardware
Size comparison of Dan "The Trak-Ball Man" Kramer's famous Atari 5200 Trak-Ball Controller with my SNK NeoGeo Arcade Joystick modded by Grips03 to work with the Atari 5200.© Lynxpro
-
From the album: Hardware
Another picture of my modded SNK NeoGeo Arcade Joystick for use with the Atari 5200, courtesy of the mad skillz of Grips03. Do yourself a favor and buy one!© Lynxpro
-
From the album: Hardware
This is my customized SNK NeoGeo arcade joystick modded by Grips03 to work with my Atari 5200. It works like a champ. Get one!© Lynxpro
-
Had the first chance to test grips03's ColecoVision Arcade Controller today and boy, this was a fantastic experience. With mounted 8-way gate I thoroughly tested Super Cobra and it's an exceptional feeling - movement is fantastic, firing and throwing bombs was never so much fun. grips, when you are reading this -> thanks again for a fantastic controller! Handling is so fine and steering objects with the knob just joyful Now I'm really looking forward to the Intellivision one