Search the Community
Showing results for tags 'upscaler'.
Found 3 results
-
I had spent quite a considerable amount of time looking for a nice HDMI upscaler for my now UAV retrofitted Atari 1200XL. The UAV did wonders for the video output, but it was ultimately let down by HDMI (or built in TV) upscalers which assumed much more on-spec video signals, with chroma and luma tolerances that react well to run of the mill comb filters. I bought the Pro version which, in addition to the CVBS to HDMI upscaling, adds support for S-Video (Y/C), Component (YbPbPr), and a few filter options which allow you to fine tune the input signal, even more. It's this guy: and you can get it here: https://www.retrotink.com/product-page/retrotink-2x-pro As you can see, it's very cost effective, compared to the Micom XRGB Framemeister, OSSC, and other upscaling solutions. How does it look? When combined with the output from my UAV modified 1200XL, the results are breathtaking. For both S-Video and Composite, the chroma to luma alignment is excellent! S-Video (Y/C) And with a nice separated chroma/luma signal, the sharpness is striking: close-up, apologies for the moire pattern. Output from PLATOTERM, Text is nice and crisp, and since it's not on Y/C, no color fringing! The P/M color overlays in ICE-T look very nice. Crisp rainbow transitions with zero fuzz in Rainbow Walker: for Ninja, the low contrast portions of background to foreground pop very nicely: Even in scenes with quick luma transitions, the upscaler does a good job with the notch filter to not introduce luma combs: COMPOSITE (CVBS) With composite, the results hold up almost as well, with the major difference being the introduction of unavoidable chroma artifacting, which, because of the well behaved notch filter, keeps luma distortion to a minimum, and makes artifact color look fantastic, as we can see here: With Jawbreaker, maze and dots render well... Let's zoom in on the jawbreaker lives, a nightmare for most composite decoders, note the smoothness: Chicken looks good, too: As does Ae 5200: And to finish, let's go back to the Rainbow Room in Ninja, with the problematic pattern that makes composite decoders cry: Beautiful, 'innit? And it really is a good thing that Mike Chi is a good guy who has a _very_ solid understanding of video signals, he has produced a solid upscaler for a decent price that will get you a superb output, especially if you've gone ahead and placed in a UAV. -Thom
-
I'm running into an odd problem that I hope someone else has seen before - I have a Sony HB-F1XDmk2 MSX2 that I'm trying to connect via RGB cable to an Extron DSC301 HD (via the 15pin D-sub input). I've done a bit of searching and believe I have the pinouts correct on both the MSX* and Extron ends. I've tested and re-tested continuity through the lines. All that said, I just can't seem to get a full picture going - I'm getting two of the three RGB colors and only the text mode (I think); the MSX boot logo screen doesn't appear, game screens don't appear. The picture is nice and crisp, there's no rolling/scrolling that I've seen mentioned from other forum posts. Also, the unit's A/V outputs work normally. The odd thing on the 2 out of 3 colors - I can swap the color lines and I'll get the blend of whatever 2 colors I hook up on the first two lines for the text, so it seems the R,G, and B are outputting from the MSX but for some reason the extron is not using/seeing/processing all three colors. I've used this d-sub input on the extron with my Apple IIgs and color/sync works. *For the 8pin DIN, I'm using the Type A pin out so 6,7,8 pins are RGB and 4,5 are the two sync lines. I also have pin 1 ground hooked up. I'm stumped - is it that I need to use a different combo of pin 3, 4, or 5 for Horizontal/Vertical Sync or is the Extron just not compatible with the MSX output? I know on paper the extron doesn't support 15kHz, but it does and works beautifully with my Apple IIgs. Most of the posts I find on this are talking about SCART connectors/wiring but I really want to make the 8 pin din to 15 pin D-Sub work if possible. Any help appreciated!
-
Hi everyone. (Long-time reader, first-time poster!) I've recently got my Jaguar set up after many years of sleeping in the loft (the Jag, not me). I'm using one of these SCART-to-HDMI upscalers. Overall, I'm pretty happy. Picture quality is decent, and Tempest 2000 sounds phenomenal through a 7.1 sound system that was the stuff of a mad-man's dreams back when it was released. However, I've just noticed that the image from the upscaler is offset down and left by about 3cm, resulting in cropping on the bottom and right edges, and a black border on the top and left. I'm guessing this is the upscaler's fault and not the Jag's, but I'm not certain (and I've got no other RGB-SCART sources to test with). Just wondering if anyone's seen something similar and (maybe) had a fix? Cheers, Chris