SlowCoder Posted April 24, 2012 Share Posted April 24, 2012 The reported fact that removing the RF modulator from an INTV II prevents the A/V mod from working caught my attention, so I dug into schematics. The video signal is created by a network of resistors connected to the AY-3-8915 and then travels through a diode (CR4) to the RF modulator. This diode MUST have DC current flowing through it, otherwise the video signal will be blocked. Studying the schematics reveals that the only possible source of this DC current is the RF modulator. Either disconnecting the video signal from the RF modulator or completely removing the RF modulator will thus remove this DC current, resulting in NO video signal to the A/V mod. To get the video signal to the A/V mod in an INTV II without the RF modulator, a new source for this DC current must be created. One possibility is to copy the INTV I circuitry - add a 3.3Kohm resistor between the video signal and +5V (The INTV I actually has 2 resistors in series with a diode, but all that's needed for the INTV II is one resistor with a value of 3.3Kohms.). Thanks! I will give this a try when I get home It's too bad it didn't work. Can you take a pic of the modification and post it? Quote Link to comment Share on other sites More sharing options...
NS7D Posted April 24, 2012 Share Posted April 24, 2012 The reported fact that removing the RF modulator from an INTV II prevents the A/V mod from working caught my attention, so I dug into schematics. The video signal is created by a network of resistors connected to the AY-3-8915 and then travels through a diode (CR4) to the RF modulator. This diode MUST have DC current flowing through it, otherwise the video signal will be blocked. Studying the schematics reveals that the only possible source of this DC current is the RF modulator. Either disconnecting the video signal from the RF modulator or completely removing the RF modulator will thus remove this DC current, resulting in NO video signal to the A/V mod. To get the video signal to the A/V mod in an INTV II without the RF modulator, a new source for this DC current must be created. One possibility is to copy the INTV I circuitry - add a 3.3Kohm resistor between the video signal and +5V (The INTV I actually has 2 resistors in series with a diode, but all that's needed for the INTV II is one resistor with a value of 3.3Kohms.). Thanks! I will give this a try when I get home It's too bad it didn't work. Can you take a pic of the modification and post it? I haven't actually done the modification, just figured out what would be necessary to forward bias CR4 to permit the video signal to get to the A/V mod. The 3.3Kohm resistor needs to be between the original video signal of the INTV II and +5V for this to possibly work (DC path). If installed properly, the DC voltage at the original INTV II video signal should be between 2 and 2.5 volts. Quote Link to comment Share on other sites More sharing options...
+5-11under Posted April 24, 2012 Share Posted April 24, 2012 The reported fact that removing the RF modulator from an INTV II prevents the A/V mod from working caught my attention, so I dug into schematics. The video signal is created by a network of resistors connected to the AY-3-8915 and then travels through a diode (CR4) to the RF modulator. This diode MUST have DC current flowing through it, otherwise the video signal will be blocked. Studying the schematics reveals that the only possible source of this DC current is the RF modulator. Either disconnecting the video signal from the RF modulator or completely removing the RF modulator will thus remove this DC current, resulting in NO video signal to the A/V mod. To get the video signal to the A/V mod in an INTV II without the RF modulator, a new source for this DC current must be created. One possibility is to copy the INTV I circuitry - add a 3.3Kohm resistor between the video signal and +5V (The INTV I actually has 2 resistors in series with a diode, but all that's needed for the INTV II is one resistor with a value of 3.3Kohms.). Thanks! I will give this a try when I get home It's too bad it didn't work. Can you take a pic of the modification and post it? I haven't actually done the modification, just figured out what would be necessary to forward bias CR4 to permit the video signal to get to the A/V mod. The 3.3Kohm resistor needs to be between the original video signal of the INTV II and +5V for this to possibly work (DC path). If installed properly, the DC voltage at the original INTV II video signal should be between 2 and 2.5 volts. Maybe try a 10K pot... in series with a ~1K fixed resistor (just in case). Quote Link to comment Share on other sites More sharing options...
ApolloBoy Posted April 25, 2012 Share Posted April 25, 2012 I wonder if there's anyone out there who'd be willing to design a new AV mod for the INTV, both of the mods I tried didn't work for whatever reason and they seemed needlessly complicated. Has anyone tried using a THS7314 or something similar with the INTV? Quote Link to comment Share on other sites More sharing options...
PacManPlus Posted April 28, 2012 Share Posted April 28, 2012 Hey Guys: There's something else wrong. The RF box doesn't work either. Something must have happened to the video circuit at some point along the mod. I'm kind of bummed, because this is my original unit from when it first came out. It sucks because I've done quite a few mods on different systems myself, and as some of you know I make carts as well. So I'm not exactly new to this. Thanks, Bob Quote Link to comment Share on other sites More sharing options...
PacManPlus Posted May 3, 2012 Share Posted May 3, 2012 Hi guys: Not being one to let things go, I removed the RF modulator again (being that it didn't help - I don't completely believe it is the correct one for the Intellivision *II*) Here are two pictures of my mod. I measured the voltage, and I am getting 2.23 Volts... but no picture. Bob Quote Link to comment Share on other sites More sharing options...
pimpmaul69 Posted May 5, 2012 Share Posted May 5, 2012 (edited) Hi guys: Not being one to let things go, I removed the RF modulator again (being that it didn't help - I don't completely believe it is the correct one for the Intellivision *II*) Here are two pictures of my mod. I measured the voltage, and I am getting 2.23 Volts... but no picture. Bob Looking at your mod it looks like you did a nice job. Only question i have is what size caps are u using. They are huge so i am assuming they are all high uf caps. I dont think all the caps are supposed to be that high. I think most of them were supposed to be like 10-100 uf Edit: also if the caps are the correct size, strangely enough with audio and video the physical size of caps can make a difference. Smaller size caps can provide more power. Edited May 5, 2012 by pimpmaul69 Quote Link to comment Share on other sites More sharing options...
PacManPlus Posted May 12, 2012 Share Posted May 12, 2012 Hi! @pimpmaul69: Thanks! They are 100uf like the instructions called for. I'll try to find shorter caps. UPDATE: I bought a new board from someone here on AA for $12 (+$8 shipping) so my old INTV II is back in business. Now - again, not being one to give up, I re-wired my old board (now, not being afraid of burning it out). The TV I have it on (I no longer have any tube TVs in the house ) is one of those that give a black screen and says 'No Signal' when it the signal isn't "strong enough" (I wish there was a way to disable that). Now, I get that message, intermingled with a scrambled picture (see screenshots). So I *AM* getting a signal, but it's not strong enough? Can anyone tell from the pics what's going on? (BTW, I'm using the 'Demonstration Cartridge' that they used to use in the kiosks to test with because it runs constantly) That particular screen actually is blue and if you click on the first pic, you can see letters. I am pretty good with electronics, but I have no clue what's going on here. Thanks, Bob Quote Link to comment Share on other sites More sharing options...
PacManPlus Posted May 13, 2012 Share Posted May 13, 2012 Hi again, guys: I am sorry for derailing the thread again, but maybe fixing this may help the OP. I found out something. The 3.3K resistor is not the right value. As I dropped the resistor value, more of the screen showed intermittently before alternating with 'No Signal'. I tried 2K, the screen came is a little better. I tried 1K, it came in even better, but still not stable. Then I tried 330ohm, and the results looked similar to the 1K resistor. I dropped down to 10ohm and got nothing again. So I *think* the real value is somewhere between 0-1K I need to find a variable resistor with that range of values because this is very time consuming. If we can figure this out, we then have a good video mod that doesn't require the RF modulator. Thanks guys, Bob 1 Quote Link to comment Share on other sites More sharing options...
PacManPlus Posted May 15, 2012 Share Posted May 15, 2012 Hi again, Guys: Here is a video I took of the screen and a close up of the modification. If anyone knows what is going on, I would appreciate it (and I think the OP would too - maybe he can remove the RF box and get a cleaner picture) http://www.youtube.com/watch?v=Ks3fOIrTROQ&feature=youtu.be Thanks, Bob Quote Link to comment Share on other sites More sharing options...
flammingcowz Posted May 15, 2012 Share Posted May 15, 2012 It might just be the TV. I had an AV modded atari that wouldn't work on any HDTV in my house. On some it would roll the picture and on some wouldn't register at all. On a good old CRT though it was perfect. Try taking to someones house that has one, or even get a cheap one on craigslist. Quote Link to comment Share on other sites More sharing options...
PacManPlus Posted May 15, 2012 Share Posted May 15, 2012 Thanks, but all of my other A/V Mods (multiple 7800s, 2600, Stunt Cycle) work great on this TV... Unless the INTV gives some strange signal that the others don't. Quote Link to comment Share on other sites More sharing options...
+5-11under Posted May 15, 2012 Share Posted May 15, 2012 Can somebody post a link to schematics for the Intellivision 1 and or 2, ideally including the RF modulator? This might help. Quote Link to comment Share on other sites More sharing options...
flammingcowz Posted May 15, 2012 Share Posted May 15, 2012 I know the INTV 1 stock output is very good. It looks like it has already been modded, but it also has an insane amount of RF shielding. Is the INTV 2 the same way, or is its stock output a lot worse than the first INTV? Quote Link to comment Share on other sites More sharing options...
PacManPlus Posted May 16, 2012 Share Posted May 16, 2012 Here are the schematics for the INTV II (although they are a little hard to read): http://console5.com/wiki/Intellivision_II At the bottom of the page, there are links to the actua schematics and the data sheet to the RF modulator. Hope this helps, and thanks, Bob Quote Link to comment Share on other sites More sharing options...
PacManPlus Posted May 19, 2012 Share Posted May 19, 2012 Ok guys - nevermind. I tossed the board. I've learned not to A/V my INTV II - it doesn't work. Bob Quote Link to comment Share on other sites More sharing options...
+cmart604 Posted May 19, 2012 Share Posted May 19, 2012 Ok guys - nevermind. I tossed the board. I've learned not to A/V my INTV II - it doesn't work. Bob Bob, let me know if you need another INTV2, I'm pretty sure I can come up with one as thanks for making so many awesome 7800 games.....and maybe as bribery to consider an INTV release or two? Quote Link to comment Share on other sites More sharing options...
PacManPlus Posted May 19, 2012 Share Posted May 19, 2012 Thanks, man - I already have another board (which is why I wasn't afraid to toss this one). I appreciate the offer! Bob Quote Link to comment Share on other sites More sharing options...
RangerG Posted October 20, 2014 Share Posted October 20, 2014 If you have an A/V modded INTV II, can you use the System Changer? Will the System Changer use the new a/v or the old rf? Quote Link to comment Share on other sites More sharing options...
pimpmaul69 Posted October 21, 2014 Share Posted October 21, 2014 If you have an A/V modded INTV II, can you use the System Changer? Will the System Changer use the new a/v or the old rf?no Quote Link to comment Share on other sites More sharing options...
papa_november Posted February 2, 2016 Share Posted February 2, 2016 I'm getting this too (wavy picture, interference, dim colors), and I bought the kit off of eBay. I'm also not getting any sound but that's probably unrelated. Is there anything specific that needs to be done for the Intellivision II? Could this be a power supply issue? Quote Link to comment Share on other sites More sharing options...
mamejay Posted June 10, 2019 Share Posted June 10, 2019 Super old thread but did anyone get a solution to this problem? Just modded one and have the same display. Quote Link to comment Share on other sites More sharing options...
+-^CrossBow^- Posted June 10, 2019 Share Posted June 10, 2019 I've tried three different types of Mod boards for the Intelly 2 and none of them looked nearly as good as the same boards used in Model 1. So I basically won't offer to AV mod an Intelly 2 because of this fact alone. I think the main issue is the fact that the model 2 has no rf shielding in it and that all of the power supply circuitry is right there next to the points you need to attach to. The model 1 looks better or at least it does for me likely because I keep the mod board inside the RF shielded section and on the far right of the system away from the power board section. Having said that, the one AV mod board that game me the overall best results was the one from the Retrofixes. But it still didn't look as good as model 1 AV modded does. Quote Link to comment Share on other sites More sharing options...
mamejay Posted June 11, 2019 Share Posted June 11, 2019 I've tried three different types of Mod boards for the Intelly 2 and none of them looked nearly as good as the same boards used in Model 1. So I basically won't offer to AV mod an Intelly 2 because of this fact alone. I think the main issue is the fact that the model 2 has no rf shielding in it and that all of the power supply circuitry is right there next to the points you need to attach to. The model 1 looks better or at least it does for me likely because I keep the mod board inside the RF shielded section and on the far right of the system away from the power board section. Having said that, the one AV mod board that game me the overall best results was the one from the Retrofixes. But it still didn't look as good as model 1 AV modded does. Thanks for that. I was thinking would this have anything to do with the power supply being used? Also would adding a voltage regulator to the 12v line to generate the 5V for the mod possibly clean up the image? Quote Link to comment Share on other sites More sharing options...
Nateo Posted November 3, 2021 Share Posted November 3, 2021 On 6/10/2019 at 1:45 PM, -^CrossBow^- said: I've tried three different types of Mod boards for the Intelly 2 and none of them looked nearly as good as the same boards used in Model 1. So I basically won't offer to AV mod an Intelly 2 because of this fact alone. I think the main issue is the fact that the model 2 has no rf shielding in it and that all of the power supply circuitry is right there next to the points you need to attach to. The model 1 looks better or at least it does for me likely because I keep the mod board inside the RF shielded section and on the far right of the system away from the power board section. Having said that, the one AV mod board that game me the overall best results was the one from the Retrofixes. But it still didn't look as good as model 1 AV modded does. Apologies for the necro-posting, but here's a thought - what if the av mod was kept outside of the case in order to move the signals away from the power supply? I mean, it's a little clumsy, but if it could result in a clean, stable image on the Intelly II, I'd gladly take it. The RF on my Intelly II is hot trash. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.