I need a new belt for my 410 and 1010...

[dafivehole]

Does anyone know a supplier for these?

 

Thank you

[russg]

Does anyone know a supplier for these?

 

Thank you

Been many years. I found one belt that fit from a package of square belts from :

 

http://www.studiosoundelectronics.com/belts.htm

 

Cost about $15 including shipping for an assortment of belts.

[dafivehole]

Anyone else?

 

Thanks,

Roger

[+orpheuswaking]

Myatari and Best Electronics have NOS belts

[Joey Z]

I found belts that worked from a broken boom box. if you have any broken tape players, take a look, some might fit.

[dafivehole]

Myatari and Best Electronics have NOS belts

 

I sent Best an email... thanks!

 

Roger

[dafivehole]

Myatari is out of them

[+orpheuswaking]

I know Best has most of them, however there are two types of 1010 and I know he is out of some of those belts....

[russg]

Does anyone know a supplier for these?

 

Thank you

Been many years. I found one belt that fit from a package of square belts from :

 

http://www.studiosou...s.com/belts.htm

 

Cost about $15 including shipping for an assortment of belts.

 

I got the CBK assortment, which had the exact good, tight belt. $13.95, plus maybe $4.00 ship. You get 10 belts, no repeats, but I think maybe more than one would work. I still have all

but the one I used, in my drawer mess. If you get the assortment then you know you will get one that fits. You have to take the drive apart, then you could try belts to get one that fits.

Since you need one for 1010 and one for 410, probably won't be the same belt. It works.

Edited August 30, 2012 by russg

[thegamezmaster]

You might try looking for a repair shop in your area that has assorted belts and see if they can match it to something. Good luck.

[dafivehole]

Best finally got back to me and they have these belts in stock

 

One question on my 1010... I have the Chelco model but they asked me if I had the square or flat belt? I am assuming that it is belt "B" in the picture below... since that belt is square I am also assuming that I will have to replace both belts on the 1010?

 

Thanks,

Roger

Edited September 8, 2012 by dafivehole

[russg]

Best finally got back to me and they have these belts in stock

 

One question on my 1010... I have the Chelco model but they asked me if I had the square or flat belt? I am assuming that it is belt "B" in the picture below... since that belt is square I am also assuming that I will have to replace both belts on the 1010?

 

Thanks,

Roger

The smaller belt is for the program counter, it is probably OK.

[dafivehole]

By smaller, do you mean "A"?

 

Roger

[+orpheuswaking]

Belt A is your drive belt, and it is flat...

 

Belt B is your counter belt (flip the unit over and you will see it is directly under the counter unit)

[santosp]

Hi guys. Can anyone sent me some belts for the 1010 and 1050 one? Bradley Coda not shipping anymore outside the USA. I will pre pay all expenses.

 

Thank you Panos.

[santosp]

Hi guys. Can anyone sent me some belts for the 1010 and 1050 one? Bradley Coda not shipping anymore outside the USA. I will pre pay all expenses.

 

Thank you Panos.

Thank you all. I found! Edited November 7, 2012 by santosp

[+Larry]

For any folks from outside the U.S., BEST does ship overseas, but only with TRACEABLE shipping. Brad got burned by claims of non-receipt, even when packages were being held in customs of the receiving country, so he will only ship with traceable delivery. Unfortunately, that means that even small package envelopes are pretty expensive.

 

Not too long ago, I shipped a small parcel to Germany which was held in their customs for several weeks, but I sent it registered, and had proof that it was in the German customs awaiting processing. Before that, I had sent a small parcel to Poland -- same deal -- weeks in customs.

 

Check with him to get the estimated shipping costs and details.

 

-Larry

 

 

Thank you all. I found!