+OLD CS1 Posted June 7, 2016 Share Posted June 7, 2016 I have a Myarc EXP-1 (512k) memory expansion. It provides a printer buffer (which I will likely never use,) a 32k RAM expansion, and a RAM disk. It is pretty handy for the latter two features, but it conflicts with the WHT SCSI card so anything I want to use with the Myarc cannot use SCSI devices. For those situations I have to physically swap in a regular TI 32k card. What I would rather do is have both in the PEB but switch them at will. Is there a way to turn off a PEB card without having to remove it? I do not mind having to make modifications to cards or PEB. Please, I know people have a lot of alternate suggestions (like the 1MB AMS,) but I would appreciate no deviation from the question. Quote Link to comment Share on other sites More sharing options...
Airshack Posted June 7, 2016 Share Posted June 7, 2016 The best way to turn off any card in your PEB is to unplug it and mail it to me. 4 Quote Link to comment Share on other sites More sharing options...
+OLD CS1 Posted June 7, 2016 Author Share Posted June 7, 2016 The best way to turn off any card in your PEB is to unplug it and mail it to me. Disappointingly, as much as I enjoy having a RAM disk, unless I can find a way to eliminate the conflict I will probably wind up ejecting the Myarc. Quote Link to comment Share on other sites More sharing options...
+arcadeshopper Posted June 7, 2016 Share Posted June 7, 2016 Disappointingly, as much as I enjoy having a RAM disk, unless I can find a way to eliminate the conflict I will probably wind up ejecting the Myarc. likely this will be the case.. you could always replace it with a horizion 1 Quote Link to comment Share on other sites More sharing options...
+jedimatt42 Posted June 7, 2016 Share Posted June 7, 2016 If you want to break ground, you might try a tripple throw switch to cut all the power sources to the card. ( maybe less throws if the card only uses fewer of the power lines... ) http://www.unige.ch/medecine/nouspikel/ti99/pebox.htm#Internal%20bus You might also get away with switching MEMEN, to temporarily lobotomize the board. Curiously, pin 12 is supposed to be PCBEN, the question is did myarc honor the that or not? I would guess nobody but TI did. I'm just guessing from the bus pinouts here. I'm also in desperate need of a SCSI controller for my Geneve, so if you want to just get rid of the WHT board, that could be a profitable option for you. -M@ 2 Quote Link to comment Share on other sites More sharing options...
+OLD CS1 Posted June 7, 2016 Author Share Posted June 7, 2016 I'm also in desperate need of a SCSI controller for my Geneve, so if you want to just get rid of the WHT board, that could be a profitable option for you. -M@ I will let you know about the WHT SCSI, depending upon the outcome of a simulation I am running: a snowball in Hell. 4 Quote Link to comment Share on other sites More sharing options...
+Schmitzi Posted June 7, 2016 Share Posted June 7, 2016 I have a Myarc EXP-1 (512k) memory expansion. It provides a printer buffer (which I will likely never use,) a 32k RAM expansion, and a RAM disk. It is pretty handy for the latter two features, but it conflicts with the WHT SCSI card so anything I want to use with the Myarc cannot use SCSI devices. For those situations I have to physically swap in a regular TI 32k card. What I would rather do is have both in the PEB but switch them at will. Is there a way to turn off a PEB card without having to remove it? I do not mind having to make modifications to cards or PEB. Please, I know people have a lot of alternate suggestions (like the 1MB AMS,) but I would appreciate no deviation from the question. Hi OLD CS1, I have the MEXP-1/512K, too, but I am still missing a powersupply for it. Means, I miss the specs for the powersupply. Is it possible to have a pic from your one´s label, with all the voltages and the polarity a.s.o. on it ? And maybe some "normal" pics, as I am documenting ALL powersupplies for the TI in this list, with pics xXx Quote Link to comment Share on other sites More sharing options...
+OLD CS1 Posted June 7, 2016 Author Share Posted June 7, 2016 Hi OLD CS1, I have the MEXP-1/512K, too, but I am still missing a powersupply for it. Means, I miss the specs for the powersupply. Is it possible to have a pic from your one´s label, with all the voltages and the polarity a.s.o. on it ? And maybe some "normal" pics, as I am documenting ALL powersupplies for the TI in this list, with pics xXx I will check to see what I can do for you. 1 Quote Link to comment Share on other sites More sharing options...
sparkdrummer Posted June 7, 2016 Share Posted June 7, 2016 I have a Myarc 512 and a WHT SCSI and don't have any issues? I use the ramdisk on the Myarc every day for lots of things and use Myarc XBII pretty frequently as well. Pretty much the reason why I probably won't get a SAMS meg card - at least right away, I gotta have these 2 things. My cru setup 1000 - Myarc 512 1100 - Myarc DSQD 1200 - 1 meg Horizon 1300 - TI RS232 1400 - WHT SCSI 1900 - Myarc 512 1D00 - Corcomp Trip Tech ?????? 1 Quote Link to comment Share on other sites More sharing options...
+mizapf Posted June 7, 2016 Share Posted June 7, 2016 I also wonder how both cards could interfere - maybe the CRU address? It responds to 1000 and 1900, so the WHTech should be placed elsewhere, as sparkdrummer showed. Quote Link to comment Share on other sites More sharing options...
+OLD CS1 Posted June 7, 2016 Author Share Posted June 7, 2016 In another thread I was going on about oddities with my Myarc 512k. I want to say it was a thread about CFHDX, but I cannot find it. I will run a quick list of CRU devices in the morning. I am pretty certain the WHT is where it should not interfere (I want to say it is set at >1700 or >1800, but I do not recall OTTOMH.) Of course, in the end I have a 1MB SAMS waiting for me at the office, so using the Myarc may be moot, anyway, but I would very much love to have it working with the WHT, irrespective. 2 Quote Link to comment Share on other sites More sharing options...
+Schmitzi Posted June 7, 2016 Share Posted June 7, 2016 Here are some of my (RMS) (and your ) configurations: (not 100%, as I am still working on it) 1 Quote Link to comment Share on other sites More sharing options...
+Schmitzi Posted June 7, 2016 Share Posted June 7, 2016 In another thread I was going on about oddities with my Myarc 512k. I want to say it was a thread about CFHDX, but I cannot find it. I will run a quick list of CRU devices in the morning. I am pretty certain the WHT is where it should not interfere (I want to say it is set at >1700 or >1800, but I do not recall OTTOMH.) Of course, in the end I have a 1MB SAMS waiting for me at the office, so using the Myarc may be moot, anyway, but I would very much love to have it working with the WHT, irrespective. this ? http://atariage.com/forums/topic/239116-myarc-512k-cru-and-dsr-craziness/?p=3251873 Quote Link to comment Share on other sites More sharing options...
+OLD CS1 Posted June 7, 2016 Author Share Posted June 7, 2016 this ? http://atariage.com/forums/topic/239116-myarc-512k-cru-and-dsr-craziness/?p=3251873 Yup, that would be the thread. Funny, I searched the forum for Myarc 512 CRU and turned up nothing. Does AA use a Microsoft search engine? Anyway, yes, the WHT is at >1700, the Myarc 512k at >1000 and >1900, and my BwG at >1100. And, as would be expected, Gazoo presented me with an option for disabling the cards by putting a switch on the ROMs. But the 32k has no ROM, so it would require a bit more surgery. Blah. Thanks for digging that thread up for me -- it has some answers I can use now. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.