Jump to content
alsp

SDrive-ARM preorder

Recommended Posts

At the begginig of April I'm expecting all parts for first 50 devices, and PCB's for 100 but when I start producing I'll able to order additional parts for remaining orders.

My collegaue will help me with assembling, so I hope to complete all existing preorders in April - May...

PS: and my 3D printer will works hard for cases =)

Ok, thanks. That is good to know.

 

Bob C

Share this post


Link to post
Share on other sites

 

Unfortunately I didn't have 810 or 1050, but i've check images of theese drives, and it seems distances almost the same like Atari800 XL. So it sholud fit...

 

Ok, I took another careful look at your device photos and I noticed a small extension (spacer?) at the bottom of the SIO plug (where it connects to the main enclosure). With that it may actually fit a 1050, I can't tell for sure because I can't tell how deep the spacer is. In any case my order is still valid as before :-)

Edited by gargoyle

Share this post


Link to post
Share on other sites

 

Ok, I took another careful look at your device photos and I noticed a small extension (spacer?) at the bottom of the SIO plug (where it connects to the main enclosure). With that it may actually fit a 1050, I can't tell for sure because I can't tell how deep the spacer is. In any case my order is still valid as before :-)

 

You righ I've made connector for ~5 mm longer than needed.

Can you measure ledge lenght above SIO jack - I can modify case if it will be required.

Share this post


Link to post
Share on other sites

Ledge length is 6mm.

Super, tnx!

it should fit perfectly.

Share this post


Link to post
Share on other sites

Super, tnx!

it should fit perfectly.

So it is going to fit... Now when will it fit. Is Russia PAYPAL ready.

Share this post


Link to post
Share on other sites

So it is going to fit... Now when will it fit. Is Russia PAYPAL ready.

So... I've already got all parts except PCBs, PCBs should be ready at beggining of April. Now I'm printing cases ;)

Share this post


Link to post
Share on other sites

How much delivery to Australia? Interested in PCB + Case + pre-programmed ARM + all required components for assembling

Share this post


Link to post
Share on other sites

How much delivery to Australia? Interested in PCB + Case + pre-programmed ARM + all required components for assembling

Delivery price should be the same - around $10

Share this post


Link to post
Share on other sites

Delivery price should be the same - around $10

Thank you. Put me down for a PCB and parts please with programmed Atmega chip.

 

Thanks

Share this post


Link to post
Share on other sites

Hi there.

 

If it's not too late, I'd take one "Assembled device - $50". With the new features mentioned: SDHC support + FAT32 Support + 8 drives support.
Deliver to PL. Thx.

What are the options for money transfer?

Kind regards.
Y

Share this post


Link to post
Share on other sites

What are the options for money transfer?

 

I think PayPal is the easiest one...

Share this post


Link to post
Share on other sites

Thank you. Put me down for a PCB and parts please with programmed Atmega chip.

Ok =) but there is non ATMega but ARM Cortex-M0 =)

Share this post


Link to post
Share on other sites

Ok =) but there is non ATMega but ARM Cortex-M0 =)

Yes that is fine. Could you just solder the cortex chip and I can do the rest. Put me down for a kit regardless.

 

Sent from my SM-N9005 using Tapatalk

Share this post


Link to post
Share on other sites

I am after one assembled device. What would the postage be to Australia?

About $10

Share this post


Link to post
Share on other sites

Put me down for one "Assembled device - $50". How much would shipping be to 85225?

 

Shipping should be around $10

Share this post


Link to post
Share on other sites

Any left?

 

It is still preorder - so yes...

Share this post


Link to post
Share on other sites

Hi! everyone!

 

Some news.

1. Almost all parts come to me for first 50 devices (except PCBs, unfortunately - still waiting).

2. For a while I'm printing cases and solder connectors into its.

3. And main news - I'm finally made "Update from SD" feature! It was not so easy, but all blocking issues are resolved and only code polishing remains. So all who will have SDrive-ARM in the future will be able update it with official or handmade firmware just by putting it on SD card.

  • Like 13

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...

  • Recently Browsing   0 members

    No registered users viewing this page.

×
×
  • Create New...