Jump to content
doubledown

F/S: Atari 5200 Controllers - Custom Joystick - Custom Paddle - Coin Controls Competition Pro

Recommended Posts

I currently have 2 custom Atari 5200 Controllers built/available, and 1 other available for sale:

 

***First my 5200 Digital Edition - VVG Enhanced Controller - $355.00 (plus shipping):

 

nsWrMk.jpg

 

Built into a beefed-up Hammond Mfg 17" x 11.25" aluminum enclosure and featuring:

*iL Eurostick 8-way joystick w/ Cherry micro-switches

*iL extended length, threaded SST shaft w/ reproduction Wico 38mm joystick ball-top (Red)

*iL PSL-L concave push-buttons w/ Rollie leaf-switches (2-Red)

*Sanwa OBSF24 24mm push-butons (1-Black/Green (Start), 1-Black/Yellow (Pause), 1-Black/Red (Reset), & 12-Black/Black (keypad buttons)

*7.5' controller cable

*Custom CPO artwork

 

The 3 potentiometers across the top of the joystick are used to adjust the resistance values for maximum left, center, and maximum right, and the 3 along the right side of the joystick are used to adjust the resistance values for maximum up, center, and maximum down.  This full-spectrum calibration allows for maximum game and console compatibility, and the potentiometer knobs are black Phenolic plastic with aluminum inlays for that vintage look and feel.  The controller comes with a Manual, and Joystick Calibration Addendum.  I recommend using Pete's Test Cartridge software for calibrating this controller to your console.  

 

More info/pics can be found in my original post regarding this controller HERE

 

***Secondly my 5200 Edition - VVG Paddle Controller - $175.00 (plus shipping):

 

YhV3wU.jpg

 

A full-featured Atari 5200 Paddle Controller.  So the base enclosure is a Hammond Mfg. black anodized, extruded aluminum enclosure, with aluminum end plates and a slide-out aluminum belly plate.  Needless to say the enclosure is extremely robust, machines very well, and is only slightly larger than a normal CX-52.   Normally the selection of a potentiometer for the control in a paddle controller is kind of a no-brainer.  Pick one with the resistance value that you require, and that has the physical attributes that will allow for its installation in your project.  But when researching paddle controllers others have made/modified for the 5200 and 2600, I had read complaints that some felt the controls were too sensitive for some games or not sensitive enough for others.  So I chose a 2-Gang, 500k ohm linear potentiometer wired through a SPDT switch, so that I can switch between 500k ohm and 1M ohm at the push of a switch.   The 500k ohm setting is less “touchy” and allows for finer movements and control, while the 1M ohm setting allows for super quick on-screen movements, like those necessary in the higher levels of Kaboom!  The resistance selection switch is located on the lower end plate and is protected from accidental in-game switching, by a clear flip-cover.  The switch to the right of the resistance selection switch is a SP3T (ON) – ON – (ON) paddle rocker switch, which is wired as the controller’s Up/Down controls.  This allows me to maneuver around my AtariMax Ultimate SD Multi-Cart menu line by line for game selection.  For the games I intend to use this with, I don’t know that I really need both 5200 buttons, but I figured as I was going all out, I might as well include both the Top & Bottom buttons...and to make it ambidextrous, I installed them on both sides.  The side buttons are Sanwa SDM-18 arcade test buttons.  They feature concave plungers for a great vintage feel, and have a nice light/short press to make the contacts. Of course it wouldn’t be a “full-featured” & “stand-alone” 5200 controller if it didn’t have its own 12 button keypad and Start/Pause/Reset buttons, so I installed a 4x4 membrane keypad with a custom overlay modeled after the original CX-52 buttons.  This allows for all game selections and auxiliary controls, without the need for a wye cable and/or a 2nd controller to be used in tandem.  It has a 9.5' cable and includes a manual.  

 

More info/pics can be found in my original post regarding this controller HERE

 

***Lastly I have a used/working Coin Controls - Competition Pro Controller $60.00 (plus shipping):

 

uG1n6X.jpg

 

Send me a PM if you're interested.  Thanks.

  • Like 3

Share this post


Link to post
Share on other sites
20 hours ago, GoldenWheels said:

Free bump because that controller is RIDICULOUS.

By that you mean ridiculously good or ridiculously expensive?

Share this post


Link to post
Share on other sites
1 hour ago, bluejay said:

By that you mean ridiculously good or ridiculously expensive?

Ha! Having built some controllers myself (none of it near THAT nice), I was just admiring the handiwork. What people ask for custom made stuff...I've learned never to blink an eye.

  • Like 2

Share this post


Link to post
Share on other sites
4 hours ago, GoldenWheels said:

Ha! Having built some controllers myself (none of it near THAT nice), I was just admiring the handiwork. What people ask for custom made stuff...I've learned never to blink an eye.

As much as I'd love a good custom 5200 controller, I don't think anyone would buy it for $355 plus shipping. I know it was well made with good parts and people do seek for these controllers, $355 is too much, but that's just my opinion.

Share this post


Link to post
Share on other sites
3 hours ago, bluejay said:

$355 is too much, but that's just my opinion.

Obviously not the target demographic ;)

Share this post


Link to post
Share on other sites
2 hours ago, OLD CS1 said:

Obviously not the target demographic ;)

Nope.

Share this post


Link to post
Share on other sites
13 hours ago, bluejay said:

As much as I'd love a good custom 5200 controller, I don't think anyone would buy it for $355 plus shipping. I know it was well made with good parts and people do seek for these controllers, $355 is too much, but that's just my opinion.

Only takes one right? I am pretty sure I have seen some of this dude's custom Colecovision controllers go for similar type pricing. You just never know.

 

 

  • Like 2

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...

  • Recently Browsing   0 members

    No registered users viewing this page.

×
×
  • Create New...