+grips03 #101 Posted September 1, 2020 Price drop, see first post. Quote Share this post Link to post Share on other sites
+grips03 #102 Posted September 7, 2020 Down to the last 3 pre modded Pro controllers (edit) and now 10 Gray. Order now if you want one. Likely won't make any more (controllers) until next summer. Quote Share this post Link to post Share on other sites
+grips03 #103 Posted September 10, 2020 Added a picture of what the RF kit (self install) looks like in the first post. Quote Share this post Link to post Share on other sites
Machine #104 Posted September 10, 2020 Amazing controllers.....dont miss out people! 1 Quote Share this post Link to post Share on other sites
K3V #105 Posted September 12, 2020 Got my pro controller today. Works great, especially with my new Wormhole 2000, too! 3 Quote Share this post Link to post Share on other sites
+Cobra Kai #106 Posted September 13, 2020 I installed the DIY kit today, had some trouble that was my fault, but it looks and works great. Am I the first one to install the kit? 2 Quote Share this post Link to post Share on other sites
+cubanismo #107 Posted September 13, 2020 3 hours ago, Cobra Kai said: Am I the first one to install the kit? I don't know, but I can confirm mine are still sitting in the envelope waiting until I have a few free nights. Care to share details on the trouble? I'm a bit of an amateur myself, and would love to avoid repeating mistakes. 1 Quote Share this post Link to post Share on other sites
+grips03 #108 Posted September 13, 2020 From the IMs it looks like this controller presses down all the time, even if the RF mod is not present on Column3. This could have been found during the first step, test your controller before modding. There are 6 wires for the mod: Two are power. Make sure to get those right. Very important. Two are for the led. One is for the mod inserting into Column3, see the table below. One is for the mod presenting a new Column3, which I call NewB to the top controller pcb. If you remove green and blue wires from the cut Column3 ribbon wire and then reconnect Column3 ribbon wire, then effectively the mod is not present (besides drawing power if the power wires are still connected). Notice the mod can only effect the signals in Column3, notice direction uses Column4. Hence the reason the RF mod cannot cause a direction issue. I have used the instructions posted in the first post to install the mod around 25 times. The instructions are very solid. In general I do not recommend the RF mod for beginner. It requires intermediate skill level for stock controllers and higher skill level for repro pro controller. Before buying mod read through those instructions and see if you are comfortable with the tool list and steps to install. In the first post, I posted pictures of the mod installed in all 3 controller types. The pictures are full size and you can zoom in. They make a good reference. For those who don't have the ability to install, but still want RF, then just buy a pre-modded controller. If anyone bought a mod kit and can't install it due to modding ability, I'm happy to take it back if its unused. Just send me an IM. 1 Quote Share this post Link to post Share on other sites
+Cobra Kai #109 Posted September 13, 2020 8 hours ago, cubanismo said: I don't know, but I can confirm mine are still sitting in the envelope waiting until I have a few free nights. Care to share details on the trouble? I'm a bit of an amateur myself, and would love to avoid repeating mistakes. Definitely fully test the controller before the mod. Also, as grips suggested, read through the installation instructions before you begin, as you will get an idea of the appropriate tools and supplies recommended for the job (various drill bits). And be extra careful with the soldering. edit: The problem I encountered during installation was I accidentally fused two of the pins together on the microchip pin 10 on 74HC244E IC While soldering the black wire to Pin 10, some solder also ended up connecting pin 9 with it, so it caused a D-Pad malfunction. 1 1 Quote Share this post Link to post Share on other sites
+cubanismo #110 Posted September 13, 2020 6 hours ago, grips03 said: It requires intermediate skill level for stock controllers and higher skill level for repro pro controller. Before buying mod read through those instructions and see if you are comfortable with the tool list and steps to install. I for one certainly am not going to be looking your direction if I mess anything up @grips03, unless it's reaching out for advice on possible repairs afterwards. I read all the docs and knew full well when I bought these that I might be pushing my abilities, and understood the risk going in. That's part of the fun IMHO! 1 Quote Share this post Link to post Share on other sites
+grips03 #111 Posted September 19, 2020 Mod kits are now on eBay as well. For picture of mod kit see first post. Quote Share this post Link to post Share on other sites
+grips03 #112 Posted October 28, 2020 Getting low on pre-build controller inventory. Quote Share this post Link to post Share on other sites
ARETHIUS #113 Posted November 17, 2020 (edited) deleted Edited November 17, 2020 by ARETHIUS deleted Quote Share this post Link to post Share on other sites
ARETHIUS #114 Posted November 18, 2020 Just got mine yesterday and I tested them today. They both work just fine. 1 Quote Share this post Link to post Share on other sites
+grips03 #115 Posted November 19, 2020 Down to the last pre-modded reproduction Pro Controller. Current inventory is in the first post. Quote Share this post Link to post Share on other sites
marcio_napoli #116 Posted November 19, 2020 2 hours ago, grips03 said: Down to the last pre-modded reproduction Pro Controller. Hi, just sent you a PM! Quote Share this post Link to post Share on other sites
+grips03 #117 Posted November 23, 2020 I'm now sold out of pre-modded repro pro controller, I still have some new gray keypad button controllers for sale. See first post for inventory. 1 Quote Share this post Link to post Share on other sites
+jgkspsx #118 Posted November 27, 2020 I must have gotten one of the last pre-modded pros. Amazing work! I've never been more average at Raiden (I used to be way below average :)) I am looking forward to putting it through its paces on as many other games as will support it... 1 Quote Share this post Link to post Share on other sites
+grips03 #119 Posted December 3, 2020 I had a couple of days free, so built some more reproduction Pro Controllers with rapid fire. 2 are ready to ship. I hope to have 8 more soon. One will be $9 off as it has a super minor defect - one less plastic ring thing where the cable exits the controller case , internally it has the upgraded LR wires and ribbon cable. 2 Quote Share this post Link to post Share on other sites
+grips03 #120 Posted December 16, 2020 I bought a clicky stick reproduction Pro Controller to see if the rapid fire 2.0 kit fits in this controller. It does not, due to the screw in the lower case's left hand riser that helps hold the clicky joystick in place. This screw would hit the rf 2.0 pcb. Quote Share this post Link to post Share on other sites
+grips03 #121 Posted 9 hours ago I have a reduced price rapid fire reproduction pro controller for sale. Its in the picture below on the left. Noticed the band where the cable comes out is missing one level at the top. Its should have 5 like the right controller, but this one has 4. Everything else about the controller is like stock. I'm selling this one for $89 + shipping. Let me know if interested. Quote Share this post Link to post Share on other sites