retrobits Posted April 10, 2020 Share Posted April 10, 2020 1 hour ago, darwinmac said: I emailed @Gavin1968 about something else. He mentioned that he uses the ili9341 for flashing. I’d start with that one first if you bought it from Vintage Computer Center. Bob C I can confirm that. I just flashed my 810S from VCC with ili9341. Now running the latest 1.2 firmware. Quote Link to comment Share on other sites More sharing options...
kraddude Posted April 11, 2020 Share Posted April 11, 2020 6 hours ago, darwinmac said: I emailed @Gavin1968 about something else. He mentioned that he uses the ili9341 for flashing. I’d start with that one first if you bought it from Vintage Computer Center. Bob C Thanks, I appreciate the reply! Quote Link to comment Share on other sites More sharing options...
a8isa1 Posted April 11, 2020 Share Posted April 11, 2020 (edited) On 4/9/2020 at 7:11 PM, BigBen said: Sorry, wrong information! "Touchlines are now auto detected! In the previous version, you had to calibrate the screen after switching on for the first time, the crosses appeared. This has been dropped." You can read the information in the readme file. What do you need? - an arduino UNO with atmega328p - an Elegoo 2,8" TFT-Touchscreen Shield or similar with ILI9341 compatible controller using 8bit parallel mode(i think, that one from the adafruit project is the same). Touchlines must be wired as followed: Update! Touchlines are now auto detected! X+ <-> 8 X- <-> A2 Y+ <-> A3 Y- <-> 9 Please pay attention to the order when flashing. FIRST eeprom_writer.hex then SDrive.hex. If you don't do it, you have to flash the Atmega again externally via a write interface. However, this requires the original data from the board. Has already happened to a friend! Hi BigBen. The v1.2 ILI9341 driver works with my ILI9338 panel. I no longer need a patch like the one I used for v1.1 Thanks! Edited April 11, 2020 by a8isa1 1 Quote Link to comment Share on other sites More sharing options...
Gavin1968 Posted April 12, 2020 Share Posted April 12, 2020 On 4/6/2020 at 1:41 PM, JGroth said: 1.5 zip doesn't have any file called eeprom_writer.hex or sdrive.hex. That is not a valid SDrive-MAX software release, the current release is V1.2, not sure what you have but that isn't correct. Also for anyone that has gotten a drive from me, I typically use ili9341 2.8" TTF's as noted above. I would also be happy to send you the latest software if you want to flash you own, all of my new drives are 1.2 at this time. Just PM/E-mail me and I will be happy to send you the two hex files needed. Thanks, Gavin Quote Link to comment Share on other sites More sharing options...
NISMOPC Posted April 12, 2020 Share Posted April 12, 2020 Direct link to github zip: https://github.com/kbr-net/sdrive-max/releases/download/V1.2/sdrive-max-v12.zip This should avoid some confusion. 1 Quote Link to comment Share on other sites More sharing options...
BigBen Posted April 12, 2020 Share Posted April 12, 2020 19 hours ago, a8isa1 said: Hi BigBen. The v1.2 ILI9341 driver works with my ILI9338 panel. I no longer need a patch like the one I used for v1.1 Thanks! Thanks go to kbr, the new software comes from him. 1 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.