Jump to content
rj1307

"Dragonfly" preorder

Recommended Posts

3 minutes ago, Defender_2600 said:

 

 

I'm reading a minimum of 1.5A, therefore it seems that a Genesis/Megadrive, SMS, Jaguar PSU is not sufficient.

 

 

345960730_Dragonflypreorder.thumb.PNG.fbd0972f89745beddf47b90bccad67b9.PNG

 

Good spot, I was going from my earlier version docs. My PSU is 1.6A so it's fine.

 

 

  • Like 1

Share this post


Link to post
Share on other sites
11 minutes ago, sramirez2008 said:

This please. I only have the standard PSUs.

 

 

 This is my PSU, the supplier is UK but I'd expect folks can find local equivalents. I know there are a bunch on Amazon similar.

 

 

 

  • Like 3
  • Thanks 1

Share this post


Link to post
Share on other sites
On 12/7/2020 at 2:15 PM, rj1307 said:

I'm starting the pre-order list for the Dragonfly SD cartridge.

Please put me down for: Dragonfly(Burgundy) + Pokey Max + YM2151 module.

 

Thanks!

James

Edited by ZeroPage Homebrew
  • Like 2

Share this post


Link to post
Share on other sites
26 minutes ago, Muddyfunster said:

 This is my PSU, the supplier is UK but I'd expect folks can find local equivalents. I know there are a bunch on Amazon similar.

The Meanwell PSUs are top value and tend to use top quality parts. They're good stuff, so if you're in the UK, worth going for (I run the same PSU).

  • Like 1

Share this post


Link to post
Share on other sites
6 hours ago, Muddyfunster said:

 

IMG_7543.jpg

IMG_7542.jpg

 

It's a nice deep red :)

Did it come with that label??

Share this post


Link to post
Share on other sites
14 minutes ago, 7800 said:

Did it come with that label??

Everyone will have this label, but if you don't like it, it's easy to peel off ;) 

 

@hizzy, any power supply with a voltage of 9V and a current of 1.5A or higher, and 5.5 / 2.1mm plugs will be good, as long as it is of good quality and will keep parameters., 

  • Like 4
  • Thanks 1

Share this post


Link to post
Share on other sites
3 minutes ago, rj1307 said:

Everyone will have this label, but if you don't like it, it's easy to peel off ;) 

 

@hizzy, any power supply with a voltage of 9V and a current of 1.5A or higher, and 5.5 / 2.1mm plugs will be good, as long as it is of good quality and will keep parameters., 

I like the label.

  • Like 2

Share this post


Link to post
Share on other sites

Of course this happens when I am tapped out.

 

I will have to wait for the next batch/release/type.

 

 

  • Like 1

Share this post


Link to post
Share on other sites

Id like to preorder, please add me to the list, for a burgundy Dragonfly with Pokey and YM2151, and converter cable. 

Share this post


Link to post
Share on other sites
5 hours ago, -^CrossBow^- said:

That is also correct. What I will likely do, is order up a 2A output rated adapter for use with a Genesis, clip the wires and reverse the polarity that way and mark it as such.

 

 

I figured you'd just get rid of the voltage regulator circuit all together and just get 4.0A 5V supply.  They are a dime a dozen these days, because of LED strips and rPI's, etc!

Share this post


Link to post
Share on other sites
Guest
This topic is now closed to further replies.

  • Recently Browsing   0 members

    No registered users viewing this page.

×
×
  • Create New...