rhcocker Posted May 25, 2016 Share Posted May 25, 2016 Sorry if this post looks familiar to anyone, I posted this in another forum and I wasn't getting any replies. I realize this might be a more appropriate forum. I completed the G7400 RGB addition mod as described here. It was surprisingly simple and took me about an hour to finish. I now need to build the 8 pin DIN to SCART cable. I am not familiar with building these, but I can't imagine it would be too difficult. So I hope someone here could give me some tips to help me complete it. Here is DIN Connector Pinout (according to the website at the link above) 1: RGB status (75 Ohm, 3 V) 2: Ground (0 V) 3: Blue (75 Ohm, 0.7 Vtt) 4: Composite Video (CVBS) (75 Ohm, 1 Vtt) 5: Red (75 Ohm, 0.7 Vtt) 6: Status CVBS (VCR) (10 kOhm, 12 V) 7: Sound 8: Green (75 Ohm, 0.7 Vtt) Here are my questions: 1) Do I add a 10 kOhm resistor to scart pin 6 and 75 Ohm resistors to scart pins 1, 3, 4, 5, and 8? 2) Does the symbol on scart pin17 (see fig) mean that I just connect it to the metal connector (pin 21)? 3) Is there anything I missing? Any help or additional info would be greatly appreciated. Thanks Quote Link to comment Share on other sites More sharing options...
Atari 2600 H.E.R.O Posted June 3, 2016 Share Posted June 3, 2016 (edited) Sorry if this post looks familiar to anyone, I posted this in another forum and I wasn't getting any replies. I realize this might be a more appropriate forum. I completed the G7400 RGB addition mod as described here. It was surprisingly simple and took me about an hour to finish. I now need to build the 8 pin DIN to SCART cable. I am not familiar with building these, but I can't imagine it would be too difficult. So I hope someone here could give me some tips to help me complete it. Here is DIN Connector Pinout (according to the website at the link above) 1: RGB status (75 Ohm, 3 V) 2: Ground (0 V) 3: Blue (75 Ohm, 0.7 Vtt) 4: Composite Video (CVBS) (75 Ohm, 1 Vtt) 5: Red (75 Ohm, 0.7 Vtt) 6: Status CVBS (VCR) (10 kOhm, 12 V) 7: Sound 8: Green (75 Ohm, 0.7 Vtt) Here are my questions: 1) Do I add a 10 kOhm resistor to scart pin 6 and 75 Ohm resistors to scart pins 1, 3, 4, 5, and 8? 2) Does the symbol on scart pin17 (see fig) mean that I just connect it to the metal connector (pin 21)? 3) Is there anything I missing? Any help or additional info would be greatly appreciated. Thanks Sir, Don't Add Resistor and, No Other Wiring/Connections. Here G7400 == G7200 (Only, In RGB To Scart Cable!) 3V/75Ohm, 12V/10kOhm, ... Are The Lines Technical/Electrical Specifications (Voltage/Impedance Specification). Good Luck. Edited June 3, 2016 by Atari 2600 H.E.R.O Quote Link to comment Share on other sites More sharing options...
Oge Posted June 8, 2016 Share Posted June 8, 2016 Depending on the voltage provided for the "RGB Status" Pin there could be a bit of be trouble. Dropped a PM to you. Cheers, Oge Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.