mantadoc Posted August 8, 2016 Share Posted August 8, 2016 Instead of all my postings i´ll keep it in this topic hope it´s ok I found Vanguard , E/A 3 game but can´t load it , any of you who can ? vanguardm.dsk 1 Quote Link to comment Share on other sites More sharing options...
Retrospect Posted August 8, 2016 Share Posted August 8, 2016 The filename to load is MAIN3O .... that is with a letter O not a zero. I went into EA option 3 and it seemed to load something ... but not run it? When I say it loaded something, I mean I did not get any error messages. It just didn't execute anything and it went back to the filename input parser. 2 Quote Link to comment Share on other sites More sharing options...
mantadoc Posted August 8, 2016 Author Share Posted August 8, 2016 Ok thanks , i used a zero Quote Link to comment Share on other sites More sharing options...
mantadoc Posted August 8, 2016 Author Share Posted August 8, 2016 Hmm... a shame it is only a demo Quote Link to comment Share on other sites More sharing options...
+Schmitzi Posted August 8, 2016 Share Posted August 8, 2016 a dem0 ? Quote Link to comment Share on other sites More sharing options...
+OLD CS1 Posted August 8, 2016 Share Posted August 8, 2016 a dem0 ? Ha! Quote Link to comment Share on other sites More sharing options...
+Schmitzi Posted August 8, 2016 Share Posted August 8, 2016 maybe this one is different ? (am too tired now) vanguardm.dsk Quote Link to comment Share on other sites More sharing options...
mantadoc Posted August 9, 2016 Author Share Posted August 9, 2016 Hmm running low for cartridge shells Any who checked for price / production of new ? Quote Link to comment Share on other sites More sharing options...
+Schmitzi Posted August 9, 2016 Share Posted August 9, 2016 Maybe watchout for cheap piles on eBay... sometimes, but only sometimes ♫ 1 Quote Link to comment Share on other sites More sharing options...
+Ksarul Posted August 10, 2016 Share Posted August 10, 2016 I'm having a friend look into producing some new injection molds for the cartridge shell design Acadiel made. . .no idea yet whether or not it will be feasible or what the cost would be (or even a timeline, as this project is one that is being pursued as time allows). 4 Quote Link to comment Share on other sites More sharing options...
mantadoc Posted August 10, 2016 Author Share Posted August 10, 2016 Ok , hmmm i tried contact a friend in thailand who had a factory producing platic and so on The tool cost around $4600,- and each shell set would cost around $3 - 500 pieces 2 Quote Link to comment Share on other sites More sharing options...
+Schmitzi Posted August 10, 2016 Share Posted August 10, 2016 4600 beach-dollar ? Quote Link to comment Share on other sites More sharing options...
mantadoc Posted August 10, 2016 Author Share Posted August 10, 2016 4600 beach-dollar ? Yes Sir , a lot of money Quote Link to comment Share on other sites More sharing options...
mantadoc Posted August 10, 2016 Author Share Posted August 10, 2016 Today i tried to use a red pcb cart with a 27512 eprom but could´n work Is it because the 378 shuld be replaced with a 379 chip ? Quote Link to comment Share on other sites More sharing options...
+Ksarul Posted August 10, 2016 Share Posted August 10, 2016 It depends on the file you are using--a Red board will work with chips all the way down to a 2764--but the files must be in non-inverted format. If you have a 27512 with an inverted image on it, it won't work with a Red board. You need to use a Black board for inverted images. Note, it is not a simple switch-out of the 378/379 between these boards either. There is a lot more going on there. Red boards use 378s and Black boards use 379s. 2 Quote Link to comment Share on other sites More sharing options...
mantadoc Posted August 12, 2016 Author Share Posted August 12, 2016 Ok Ksarul thanks :) Quote Link to comment Share on other sites More sharing options...
mantadoc Posted August 12, 2016 Author Share Posted August 12, 2016 Ok thanks again Ksarul , i bank inverted the file to put on the red pcb then it works 2 Quote Link to comment Share on other sites More sharing options...
mantadoc Posted August 15, 2016 Author Share Posted August 15, 2016 Grom configuration : What am i doing wrong when i use the Gromcfg , when i press 6 for base and E for Eeprom then it´s disapear again ? Have i forgot to do something ? I tried to see the help video Quote Link to comment Share on other sites More sharing options...
Tursi Posted August 16, 2016 Share Posted August 16, 2016 Do you have your GROM cartridge plugged in at the time you are doing it? The display in the top left pane is generated by reading the actual config in the UberGROM chip, so if you don't have it attached, no settings will appear to take. Quote Link to comment Share on other sites More sharing options...
mantadoc Posted August 16, 2016 Author Share Posted August 16, 2016 ooh can i not use Classic99 to do it ? Quote Link to comment Share on other sites More sharing options...
Tursi Posted August 17, 2016 Share Posted August 17, 2016 You can use Classic99, but you must configure an UberGROM cart in Classic99.ini and select it in order to tell the emulator that you are using the UberGROM, otherwise it has no way to know. Demonstration here: https://www.youtube.com/watch?v=JWnjDYQJqVU Also see this post for a sample Classic99 entry and a modified version of Editor/Assembler that can be used as shown in the video: http://atariage.com/forums/topic/244707-preparing-an-avr-as-an-ubergrom/?p=3472615 1 Quote Link to comment Share on other sites More sharing options...
Like us on Facebook
Follow us on Twitter
AtariAge on Instagram
Watch us on YouTube
Chat on Discord
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.