Jump to content

KLund1

Members
  • Posts

    894
  • Joined

  • Last visited

Recent Profile Visitors

12,268 profile views

KLund1's Achievements

Dragonstomper

Dragonstomper (6/9)

341

Reputation

  1. Thanks both of you. I appreciate the replies. Audiolabga.com seems to only have flat and square belts. I think 410 need round belts. I have not tested square belts on rounded pulleys. Will they work, or wear down quickly?
  2. Hi I have a 4 belt 410 that I need new belts for. I found below in another thread. And I assume they are round belts? But I have no idea where to buy these belts in the USA. CPC seems to be a UK firm, and these are not available anyway. Console5 is still out of stock, and BEST has NOS that are just too old and will probably break soon. I have purchased several cassette belt lots from china on ebay. None have belts that fit, except the small counter belt (not listed below) I did find the 97mm belt but at $14 each plus $13 to ship seems ridiculous to me. I have asked this on other threads but no replies so I am starting a new one. On another thread I found this link for drive wheel rubber replacements https://www.lowes.com/pd/Danco-11-16-in-Rubber-Washer/3712656 Any help from Atari Pros out there? Thanks Report Posted April 7, 2016 I'm not well equipped to estimate whether a 1mm difference in size will be bad for my tape unit. Will tiny differences in size make a big difference? Assuming these numbers are correct (I have not ordered belts yet, but I am in the process of trying to source these), the size in inches should be: Rewind: 3.82" x 1.2mm (0.47") Fast Forward: 4.45" x 1.1mm (0.43") Play: 7.91" x 1.2mm (0.47") The CPC part numbers no longer appear to be accurate. And there don't seem to be corresponding sizes in stock for all of those.
  3. Thanks I did that. I got several sets, none with proper sizes or shapes. If you know of a specific set that would work from aliexpress, please post a link
  4. HI, bringing back to life an older topic. I need some belts for a 4-belt version 410. Concole5 is still out of belts, and the several sets of cheap belts from ali-epress that were each different did not have the right sizes; too thin, too short, too long, or too wide. Anyone have a source for correct belts as of 3/11/2024? Side Q; So there is the original carry handle version(one with and one without power cord) - 2 belts And there is a 2 belt, and a 3 belt, and a 4 belt version of the later, slightly smaller and rounded corners, and more numerous 410's ? If so, how to tell them apart? Thanks
  5. I pulled out my 825's to give them a once over. Having them side by side for the first time, I noticed that they are significantly different on the inside. Has this been documented elsewhere before? (side Q; what is a good replacement for the deteriorating foam?)
  6. I have an early AII with a rev 0 keyboard. most of the keyboard switches are not working. A few on each row work so it is not the chips on the PCB. I tested them all with an Ohm meter, and marked which are not working. I have tried DeOxit D5 on one, pressed 50 times, no change. Electronics contact cleaner on another, pressed 50 times, no change. Compressed air on a third, and the the two after I already tested them,, pressed 50 times none worked. I submerged in ISO,, pressed 50 times, let dry, no change. I reflowed the solder joints, no change. I took one apart and polished all the copper inside and reassembled. That is NO EASY task. Start to finish took about 3 hours for one switch! Almost lost both tiny springs several times! And it still did not work. (not working I mean by testing with an ohm meter, not powering up the AII) I saw people using an ultrasonics cleaner for their cherry key switches and it seemed to work great. Would that work for these switches? Thoughts, ideas, suggestions ?? Thanks
  7. _The Doctor_ Agreed !! bfollowell Thanks. I got a set of those, before I found this fax machine.
  8. I came across a old dead McGraw Hill / Texas Interments 745 Portable acrostic fax machine, Part No 0983801-0003 It has the exact same white plungers the the 800 uses. When I saw it, there were several keys missing and I saw the plungers. I pulled one out and compared to my 800 and they are exactly the same. Most were cracked at the corners like 800's but about 20 were still good. So FYI for a possible source for parts. I found this in a junk pile at a e-recycler. fyi the springs are too ling for 800's, but could be cut down. At least they are the right diameter and springiness.
  9. https://slcc.wdgeo.com/ https://www.facebook.com/people/San-Leandro-Computer-Club/100069815269539/ PM me for a ZOOM link/invite
  10. Agreed for the X-Mas colored cases. When I saw the black case, I hoped the bottom was black too. Then I was thinking that this might be something like the Bell & Howell Apple II cases. The top case I had must have been a test color by Atari. As I said it was not painted. Also it did not have the cartridge/ram cover.
  11. I had a black molded 800 top case a cleaned up for a friend that then sold it on ebay for a lot. It was not painted. It was black plastic throughout. It had some texture, but was smoother and more reflective. There were a couple nicks in the plastic that showed that it was not painted. But I do not have those pictures.
  12. Anyone have a solution to any of these problems? The lag issue is terrible on BT for most games. With wired controllers, about 15% of the installed games have a significant enough lag to be almost unplayable. I get about the same for games load from an SD card for any platform. I hope a Bios or OS updates is coming soon. Side note: There are no instructions for the games the come with the systems. Nor is there a link I can find to the instructions. Most games, most people know, but there are many that the general public does not know how to work/run/use/play. The paragraph they include is not enough for the less popular or more complicated games. I hope an OS update will help with this. Thought from the community??
  13. HI all !! I want to buy a mini pc that can store ALL emulators and games from 1976 - 2005. I have a GameStick PS/2, 2 person controller I want to use this with. I want to put the PS under the unit, and have it wifi, or HDMI to the main big TV. Then Bluetooth, or wired to the game controllers. Most mini PC these days can handle the run load. But few have the onboard storage to hold all that data. I think is is about 1.5TB up to PS1 games, then to about 4Tb to PS2 games. (that is all console platforms) My budget it not large. I have tested a couple mini-pc's. One fast, but no expandable storage, no wifi, no BT. The other, lesser performance, but with slower SD card HD store, no wifi, or BT. I want a mini PC with, less cores-faster speed, more cores-less speed (hopefully less heat), both with 4Tb HD/SD/M.2 plus online fairly fast access storage. OH, it MUST have USB 2.0 hub compatibility. I know this is a lot to ask in this forum. But, I know there must be someone here that at lest point me in the right direction. Many thanks!
  14. SLCC - ATARI In Person & Zoom Meeting 11/7/23 6:4Bpm San Leandro Main Public Library. PM for zoom invite
×
×
  • Create New...