-
Posts
496 -
Joined
-
Last visited
-
Days Won
1
dphirschler last won the day on May 2 2022
dphirschler had the most liked content!
About dphirschler
- Birthday 03/08/1968
Contact / Social Media
Profile Information
-
Gender
Male
-
Location
Kennesaw, GA
Recent Profile Visitors
dphirschler's Achievements
Dragonstomper (6/9)
349
Reputation
-
3D printed TI99 VGA port for F18A
dphirschler replied to dphirschler's topic in TI-99/4A Development
Made a stock AV panel in case you wanted to go back. And I may add a USB for external keyboard. Darryl -
Cherry MX compatible upgrade for Mitsumi 99/4A keyboards
dphirschler replied to visrealm's topic in TI-99/4A Development
I think the HI-TEK keyboards are also a good candidate for this upgrade. Darryl -
3D printed TI99 VGA port for F18A
dphirschler replied to dphirschler's topic in TI-99/4A Development
-
- 1 reply
-
- 13
-
Hackaday project: keyboard PCB replacement
dphirschler replied to retroclouds's topic in TI-99/4A Computers
Eagerly waiting for this. I have two Mitsumi keyboards that I've been wanting to restore. I like that you included the Alpha-lock fix as well. Darryl -
3D printed TI99 VGA port for F18A
dphirschler replied to dphirschler's topic in TI-99/4A Development
I did, but understand the modified piece I made was only to test that it would fit the console without having to cut it. The test fit went well; in other words, it fit on the internal posts and up against the back edge like it should. So I believe the original part should fit a black console. The pic in the above post should show the modified part in a black console. Darryl -
3D printed TI99 VGA port for F18A
dphirschler replied to dphirschler's topic in TI-99/4A Development
I believe it will fit the black console too. But I have not cut a black console shell to test fit it. I did modify the piece so that I could test fit it in the black console without cutting it and it fit. Darryl -
3D printed TI99 VGA port for F18A
dphirschler replied to dphirschler's topic in TI-99/4A Development
The VGA AV panel has been published on Thingiverse. Please test it out and give feedback, especially if you have a MK1-F18A. Also, some refinements have been made to the piece. It might actually be possible to keep the (modified) RF shield. I would be curious if this is true. So again, I would like your feedback concerning this. https://www.thingiverse.com/thing:6560819 Darryl -
3D printed TI99 VGA port for F18A
dphirschler replied to dphirschler's topic in TI-99/4A Development
The VGA AV panel has been published on Thingiverse. Please test it out and give feedback, especially if you have a MK1-F18A. https://www.thingiverse.com/thing:6560819 Darryl -
3D printed TI99 VGA port for F18A
dphirschler replied to dphirschler's topic in TI-99/4A Development
Here is how the VGA cable is held down. M2x20mm screws secure it to the main part. I am working on another design which just uses a VGA port that you solder the wires to. -
3D printed TI99 VGA port for F18A
dphirschler replied to dphirschler's topic in TI-99/4A Development
I am not a fan of hot glue. Darryl -
3D printed TI99 VGA port for F18A
dphirschler replied to dphirschler's topic in TI-99/4A Development
-
Originally posted on FB... After putting it off for a few years, I finally made a nice looking VGA port for the TI99. Here is my design. I haven't yet tested it on a black console yet, but I am sending it out to a few people to try. It requires you to remove the original AV port and solder your audio wires to the board. And it also requires you to cut a rectangular hole on your console shell 60x16mm. More details to come. EDIT- Posted on Thingiverse: https://www.thingiverse.com/thing:6560819 Darryl
- 15 replies
-
- 11
-
For those playing on DS99, map START and SELECT to 1 and 5. Makes it a whole lot nicer to play. Darryl
-
If I am not too late, I would like to beta test for you. I have a small amount of homebrews that I would like to test out. Darryl