KLund1

Understood. Many thanks for the quality advice. Will order same value parts.

Tested Cap in the "hot" area with my incircut DCR tester. and bad news C41, C99 and the big one C39 all read low. And of course I do not have any new of that size. I use a standard rebuilt Atari PSU with near perfect output. Now adding to my DIgiKey shopping list. C41 & C99 are 22uf 16v. Is there a better uf and voltage that would be better there. The C39 is 10,000uf 16V are there better values for this too? Thanks

Thanks thanks. The 800XL was a 3 point connection not 4. Very much appropriate the kind offer. This community is always helpful. Any know the right part to buy. Again thanks

I have a similar problem with this 800xl color potentiometer. The unit I'm trying to bring back to life has lost the top plastic part. It does not make good contact between the halves. It needs replacement. Easy fix if I have the right part. Could one of you parts guru's point me to the correct part on digi-key, please. I think it is a 500K, at least that is printed on another 800xl I have. (an aside, I looked at the Best Catalog, and did not see any potentiometers listed. Guess he does not have everything in that book.)

I think it was just sitting the FujiNet main screen. It was probably sitting a good 4+ hours idle with I got back and noticed it. (a/c room 75', not in sunlight) More testing with various setups and it get very warm with my SpartaDOS X Super Cart running. Just looking at disks dir's and some disk formatting on a USD 1050. Oh, moved a few files. Nothing major. It is less hot with other carts, games. Warms up more with use, loading files from internet, or coping from internet to SD. Does get hot with "printing" a long Basic listing, but that would seem normal as the radio is in heavy use. But it is very hot. I would not want to touch the heat sink! The outside cart and case were quite hot. I bring this up as I am going to show it this weekend at VCF-W. It will be on probably 8 hours straight, 2 days. I will put a small fan on it just to be cautious.

I found another Action! Cart. This is a black 1 eprom cart. ?$B8000 shows 32768, $B8000 = (heart) $0000 0 0 Attached a rom dump of it. Hope this help too. Action! Black Cart (mbm27128).BIN

I have been using FujiNet a lot these past few days. Learning how to use it. Wonderful device! After a couple hours, I have noticed the FujiNet, and just the right on the unit at the rear of my 1200XL, it gets VERY Hot. I'd guess about 110'-120'f. You do not want to leave your hand there. I do not have a fancy remote thermometer to get an accurate number. I have tested this a bit further and it is about the same while in use with wifi, and idle and connected to wifi. I noticed this after I had let the system stay on when I went to run some errands. When I came back there was lots of noise on the left side of the attract screen. Attract worked changing colors. but the otherwise the system was locked up. I went to press the fujinet reset button and noticed the heat! lots of it. After I let both cool, and restarted they were working normally. Then I monitored the temps as noted above. Before I noticed the heat, I had upgraded from ver 1.3x to 1.5x. Is this normal? What more info is needed to be helpful

Yes I have seen your site. I did not make the mental connection, sorry. You helped me with designing some Diagnostics cart labels a year ago. Great to see you on our club SLCC Zoom call a few weeks ago. Hope you can attend again when you have the time.

I seem to have misplaced my instructions/manual for this cart. I searched in here but the terms are a bit too general to find it. Can a kind soul point me in the right direction please? Thanks

WOW !! Thanks. I think it looks great. You obviously have done quite a bit of research for this. Bravo! I'm glad you put this up here fort the whole community to enjoy.

I think Select Reset brings up the RomDisk. And yes it is German. But docs are now easily translated. I'd like to play with it a bit as it sits in my 32-in-1 OS. But needs a manual or something.

Anyone have a manual, instructions, guide, or anything on how to use this OS ? I did some googling and did not find much. It has something called a ROMdisk. Thanks

Mr Robot, Many thanks ! Any idea which sub font the badge is? I think the numbers are a different font, and a different color.

x00's = computers 810's = drives 820's = printers 830's = modems 850 = interface 840's = monitors? 40=12" 45=14" 47=19" ??

I would like to make some imitation/fictional 800 (not xl/xe) front badge labels. Anyone have these fonts anywhere? I know to letter and numbers are different fonts. I would like a label that shows 840 instead of 800. Any ideas or suggestions? Thanks !

Thanks Swamping disk manually would be ejecting both slots. navigating to site then sub-directory and find file (how to filter?) put in new slot. Rinse and repeat for other slot. That seems time consuming. While in the TNFS Host List, press tab to get to drive slots, and pressing I assume is A button, nothing happens. How to rotate with button? I can't find any docs about connecting with blutooth on the github wiki or fujinet wiki. Reading on the one of the wiki's, fujinet has a problem loading AtariWriter, SO how did the guy do it in the video above?

Thanks That is a lot of help !! All questions answered above Except: -In the above video at about the 6 minute mark he load NCD what is this? I understand about this now. Next he magically loads AtariWriter. What steps did he use to do that? -How to get back out of an application or game to the Fujinet menu without switching off the computer? -When I am in atari-apps.irata.online how to filter a large directory for files that start with ST for example? New questions -how to move (if possible) Drive Slot 4 to 1 and 1 to 4, for example, so it will boot. Or can it boot from drive slot 4? (seems unlikely as you normally cant boot from D4) Again thanks everyone!

I have another working cart with Roms I'm not sure how to read in my TL866 II+ They are EXEL 8423 XL-S-2365-P-300 ATA0010SAC high X00022 Since these are not EProms, I'm assuming these are ver 3.6. But I'd like to dump them just in case. But I have third cart that will not fully boot. Here are the bins for it. Can anyone one of you a lot smarter then me pro's out there figure this one out? I'm hoping these are of some value to the comunity Acation Bad OSLA rom.BIN Acation Bad OSLI rom.BIN

I have an Action! cart that shows $B000 = 5 $1035 53 4149 Version 3.5? Bins attached Action L rom (mbm2764).BIN Action H rom (mbm2764).BIN

More questions In the above video at about the 6 minute mark he load NCD what is this? Next he magically loads AtariWriter. What steps did he use to do that? does not a warm boot remove the NCD settings? He, a bit later, says he has his admin setup for a 1027 printer. How is that done? Also I am no good with network stuff. My desktop is wired directly to my router. Fujinet is connected to the hotspot on my phone. They can't connect to eachother? If I connect fujinet to the router wifi, can my desktop connect to it? If so, or when I can what address do I use? How to get back out of an application or game to the Fujinet menu without switching off the computer? I have an Ultimate cart. How can I use that with the Fujinet? When I am in atari-apps.irata.online how to filter a large directory for files that start with ST for example? Again many thanks for any help with my many questions.

Sorry for the nubie questions. But just got my Fujinet 1.3 unit and just starting to use it. First thing is the quick start page appears broken. no joy on Chrome, firefox, or Andriod phone https://fujinet.online/#post-inner I wanted to see what the buttons are for and what combinations of presses do what. How to access the SD card I inserted into it. I am able to connect fujinet to wifi. I can connect to atari-apps.irata.online.I can put DOS 2.5 in drive slot one. I select W option. When I 'boot' I hear dos loading. I am then in BASIC. I type DOS and it goes to selftest. Why not DOS? I saw the Fujinet load the dos file into device 11 How can I set it up to load files at the very fast speed shown in this video. I just get 'normal' load rate Thanks for your understating and for the help.

I have been away for a while, and am just starting to learn about this incredible device. I have watched a couple vids about it. And really like its capabilities! My Atari daily driver is a Atarimax 1200XL with a 32-in-1 OS selector. Is the new device compatible with the 32-in-1? I did a few quick searchers and did not see any results about this particular topic. Though I may have missed something in my recent absence. (in the middle of a house remodel) Sorry for interrupting the above conversation.

Wow !! I did not see that either. Sorry about posted with out looking closer! I have used one of these for 240v items https://www.grainger.com/product/30C515?gclid=Cj0KCQjw-uH6BRDQARIsAI3I-UfHZKRyG6pNHkn9uAYrsvKp4hWZLN3cn0BcB8qPL4S6zl8XFNrxvkAaAr2NEALw_wcB&cm_mmc=PPC:+Google+PLA&ef_id=Cj0KCQjw-uH6BRDQARIsAI3I-UfHZKRyG6pNHkn9uAYrsvKp4hWZLN3cn0BcB8qPL4S6zl8XFNrxvkAaAr2NEALw_wcB:G:s&s_kwcid=AL!2966!3!281698275255!!!g!471571925921!&gucid=N:N:PS:Paid:GGL:CSM-2295:EUGDJC:20500731 It is not too expensive. I has come in handy a few times with stuff I got from euroupe, and for friends that had similar computer items.

Many Thanks !!

Thanks!!! Very helpful. Much appreciated!