RickyDean

Yea, I searched a few days ago without finding anything, that is why I am going this route.

@JasonACT, I figure if I can't fit them on, I can always use the bigger memory, no foul.

I've been tinkering with @JasonACT's toy. I am adding two uson pads (circled) for APS6404L-3SQR-ZR uson memory ic's as I accidently bought 10 of these on my first try of ordering the BOM for this device instead of APS6404L-3SQR-SN sop. It was a time trying to figure out where to put the first one that corresponds to U2, the one in U7's footprint was much easier. I hope these don't violate design rules to much and are producable. And as @JasonACT states below the 74LVS245 is 74LVC245 now on my drawing. This is just for me to use up my stock of uson memory.

Not knowing how you installed the russian diodes, you are aware that they need to be placed int their locations with the black band reversed from an American diode correct? Not aware if this could be part of the issue, but maybe worth looking at.

That may be where I have an issue then. I'm was assuming that I needed to program this sketch into the machine, so I've played around with the programmer, because upload for me wasn't persistent, at least I thought it wasn't, for after the pulling it from the laptop, it wouldn't run from just the Apedsk. I may have overwritten the boatloader. From the sketch menu after I verified and compiled the sketch I saved the compiled part to the sketch, one is called a bootloader and smaller and one called larger which must be the rest of the code. Can I take my TL866 Minipro and burn that bootloader, if so at which address should I start it. Then what address should be the start address to burn the other larger .hex file.

What would I use here?

You probably corrupted the menu in the 8k IC on U9, don't know if you've lost the data in the other memory IC's, you can try reloading just the ROS without formatting the card again and see if it will recover. But be prepared to reload the complete ramdisk @InsaneMultitasker and others would have much more knowledge here.

Her would be your six diodes in the upper right central of the schematic

I need to correct that the can style transistor should point upper left not right.

Here are the schematics of the 4000B card, in this thread. You can start running traces to see if something is not right in your build. @Ksarul's 4000B build is rock solid and he does a pretty good schematic too. Using the construction manual, these schematics, and the working card, you should be able to trouble shoot this issue. I believe it's a construction issue, solder joint, reversed diode, or something along that line. Just to check are you using this Ramdisk on a Geneve? or on a TI? Are you using the 32k upgrade at M32 on the Board or leaving that off and using a 32k card internal/external? Are you leaving the the IC at U11 off if you are not using the 32k otion on board? Do you have both transisitor mounted so that the flat side faces toward the bottoms of the board, or if using the can type transistor, being sure the tab is pointed toward the upper right corner of the baord?

@JJB I took and restarted the IDE and tried to load and program, still got the error. I then closed the sketch, quit the IDE, and unzipped the Apedsk99 stuff over the other files. I then tried to upload and program and still got the error. I then tried just to upload the sketch and it did so. Then leaving it connected to my laptop I walked into the computer room and hooked the APEDSK up to the TI, went into TI Basic and typed in the CALL AHLP and I got the correct response with your info. So it is working, it just won't let me upload and program it to the ATMega328P AVR. How do I set up the IDE to correctly load and program the booloader and files to the AVR. I did, after compiling, save the compiled binary, and both hex files, bootloader and the other are in the folder with your sketch files?

Pin one of the U1, the 74LS154 ties into the pin 22 "CS" of the M1 memory location. Did you try changing the 154, as it may have a short. I don't have batteries on mine to check it with currently.

Has it done that since the build? If so after you do the IC tests, then I'd start looking for possible shorts under the sockets, starting with the 244's. Take a multimeter and see if you get continuity between two pins then investigate to see if you have a solder blob or a small solder ball ot wire piece shorting out a chip. If you find a possible short, check the same pins on your good 4000 to be sure that it is not doing the same.

I'd change out every IC, one at a time, excluding the meory IC's. You may find one is bad and have it narrowed to that one. Did you build these recently? I've built three, One over 20 years ago, 2 about 2 years ago.

I thought of that last night after posting these pictures, but even after changing it, it is still not working. Will try restartingthe IDE later today and see if that makes a differeence.

Well two of my new ink cartridges would not be accepted by the 8710, but I went to this site and tried the solution they recommended and it worked. Downgraded my printer firmware. https://www.themakersphere.com/non-hp-chip-detected-fix/ May help some of you.

Did you test the 74LS244 Ic's, to be sure their functioning correctly. Maybe change them with the other 4000 and see if it fixes this one and makes that one behave as this one is?

Here are some scans of the UNO and package it came in from China. No I have only tried to load this sketch as I'm not that familiar with programming these devices. Usually if I don't have explicit instructions, I find it difficult to program them correctly, UNO, teensy, STM32, Beagle Bone, Pico, etc. Here's where I got it from. https://www.aliexpress.us/item/3256802811531752.html?spm=a2g0o.order_list.order_list_main.5.21ef1802jSY3o1&gatewayAdapt=glo2usa

Thinking the same myself. They're wanting someone running Windows to only use MS approved, aka. "licensed" "certified", software?

That was weird I was working on adding this and the whole atariage went down giving me a 503 service error. @JJBOkay I had to move around your library files and delete some already installed libraries and got it to show different errors now and found that you had already created the sketch, I was creating a new sketch as I'm not all that familiar with programming controllers. Maybe I on the wrong Arduino IDE for this build? I did try uploading what I had but all that worked was the 32k. " Arduino: 1.8.19 (Windows 10), TD: 1.58, Board: "Arduino Uno WiFi" C:\Users\Ricky\Downloads\APEDSK99-APEDSK99_current\Arduino\APEDSK99_012s\APEDSK99_012s-C-global_suppfnc.ino: In function 'boolean prepDSK()': C:\Users\Ricky\Downloads\APEDSK99-APEDSK99_current\Arduino\APEDSK99_012s\APEDSK99_012s-C-global_suppfnc.ino:103:56: warning: ISO C++ forbids converting a string constant to 'char*' [-Wwrite-strings] Acatpy( DOADfilename, sizeof(DOADfilename), ".DSK", 4); //stick default file extension at the back ^ C:\Users\Ricky\Downloads\APEDSK99-APEDSK99_current\Arduino\APEDSK99_012s\APEDSK99_012s-C-global_suppfnc.ino: In function 'void CALLstatus(byte)': C:\Users\Ricky\Downloads\APEDSK99-APEDSK99_current\Arduino\APEDSK99_012s\APEDSK99_012s-C-global_suppfnc.ino:132:53: warning: ISO C++ forbids converting a string constant to 'char*' [-Wwrite-strings] writeCBuffer( 2, 18, "\0", 0, true, false, '\0' ); ^ C:\Users\Ricky\Downloads\APEDSK99-APEDSK99_current\Arduino\APEDSK99_012s\APEDSK99_012s-C-global_suppfnc.ino: In function 'byte readFATts()': C:\Users\Ricky\Downloads\APEDSK99-APEDSK99_current\Arduino\APEDSK99_012s\APEDSK99_012s-C-global_suppfnc.ino:233:1: warning: no return statement in function returning non-void [-Wreturn-type] } ^ C:\Users\Ricky\Downloads\APEDSK99-APEDSK99_current\Arduino\APEDSK99_012s\APEDSK99_012s-F-FD1771cmd.ino: In function 'void loop()': C:\Users\Ricky\Downloads\APEDSK99-APEDSK99_current\Arduino\APEDSK99_012s\APEDSK99_012s-F-FD1771cmd.ino:19:23: warning: suggest parentheses around assignment used as truth value [-Wparentheses] if ( newFD1771cmd = ( currentFD1771cmd != lastFD1771cmd ) ) { //new or continue previous FD1771 command? ~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ C:\Users\Ricky\Downloads\APEDSK99-APEDSK99_current\Arduino\APEDSK99_012s\APEDSK99_012s-G-AD99cmd.ino:6:22: warning: suggest parentheses around assignment used as truth value [-Wparentheses] if ( newA99cmd = (currentA99cmd != lastA99cmd) ) { //new or continue previous APEDSK99 command? ~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ C:\Users\Ricky\Downloads\APEDSK99-APEDSK99_current\Arduino\APEDSK99_012s\APEDSK99_012s-G-AD99cmd.ino:48:63: warning: ISO C++ forbids converting a string constant to 'char*' [-Wwrite-strings] writeCBuffer( 1, 11, "\0", 0, true, false, '\0' ); //read/save filename characters in CALL buffer ^ C:\Users\Ricky\Downloads\APEDSK99-APEDSK99_current\Arduino\APEDSK99_012s\APEDSK99_012s-G-AD99cmd.ino:64:70: warning: ISO C++ forbids converting a string constant to 'char*' [-Wwrite-strings] writeCBuffer( 12, 15, "PRG", -12, false, false, '\0' ); //must be "PRG"; write to CALL buffer ^ C:\Users\Ricky\Downloads\APEDSK99-APEDSK99_current\Arduino\APEDSK99_012s\APEDSK99_012s-G-AD99cmd.ino:204:64: warning: ISO C++ forbids converting a string constant to 'char*' [-Wwrite-strings] Acatpy( DOADfilename, sizeof(DOADfilename), ".DSR", 4); //stick extension at the back ^ C:\Users\Ricky\Downloads\APEDSK99-APEDSK99_current\Arduino\APEDSK99_012s\APEDSK99_012s-G-AD99cmd.ino:270:66: warning: ISO C++ forbids converting a string constant to 'char*' [-Wwrite-strings] writeCBuffer( 18, 28, "\0", 0, true, false, '\0' ); //read/save DSK name characters in CALL buffer ^ C:\Users\Ricky\Downloads\APEDSK99-APEDSK99_current\Arduino\APEDSK99_012s\APEDSK99_012s-G-AD99cmd.ino:279:73: warning: ISO C++ forbids converting a string constant to 'char*' [-Wwrite-strings] writeCBuffer( 3, 12, "<no map>", -3, false, false, '\0' ); //DSK not mapped ^ C:\Users\Ricky\Downloads\APEDSK99-APEDSK99_current\Arduino\APEDSK99_012s\APEDSK99_012s-G-AD99cmd.ino:304:76: warning: ISO C++ forbids converting a string constant to 'char*' [-Wwrite-strings] writeCBuffer( 18, 27, "t= f=", -18, false, false, '\0' ); ^ C:\Users\Ricky\Downloads\APEDSK99-APEDSK99_current\Arduino\APEDSK99_012s\APEDSK99_012s-G-AD99cmd.ino:338:60: warning: ISO C++ forbids converting a string constant to 'char*' [-Wwrite-strings] if ( !Acomp(DOADfilename, 9, "SYSTEM~1") ) { //skip SD system folder ^ C:\Users\Ricky\Downloads\APEDSK99-APEDSK99_current\Arduino\APEDSK99_012s\APEDSK99_012s-G-AD99cmd.ino:374:64: warning: ISO C++ forbids converting a string constant to 'char*' [-Wwrite-strings] writeCBuffer( 11, 21, "\0", 0, true, false, '\0' ); //write TI DSK name to CALL buffer ^ C:\Users\Ricky\Downloads\APEDSK99-APEDSK99_current\Arduino\APEDSK99_012s\APEDSK99_012s-G-AD99cmd.ino:382:70: warning: ISO C++ forbids converting a string constant to 'char*' [-Wwrite-strings] writeCBuffer( 23, 28, "S/ D/", -23, false, false, '\0' ); ^ C:\Users\Ricky\Downloads\APEDSK99-APEDSK99_current\Arduino\APEDSK99_012s\APEDSK99_012s-G-AD99cmd.ino:404:61: warning: ISO C++ forbids converting a string constant to 'char*' [-Wwrite-strings] writeCBuffer( 1, 30, "\0", 0, true, false, '\0' ); ^ C:\Users\Ricky\Downloads\APEDSK99-APEDSK99_current\Arduino\APEDSK99_012s\APEDSK99_012s-G-AD99cmd.ino:421:61: warning: ISO C++ forbids converting a string constant to 'char*' [-Wwrite-strings] writeCBuffer( 0, 32, "\0", 0, true, false, '\0' ); //... yes, write next chunk of 32 definition bytes to CALL buffer ^ C:\Users\Ricky\Downloads\APEDSK99-APEDSK99_current\Arduino\APEDSK99_012s\APEDSK99_012s-G-AD99cmd.ino:206:11: warning: this statement may fall through [-Wimplicit-fallthrough=] if ( SD.exists(DOADfilename) ) { //does new DSR exist? ^~ C:\Users\Ricky\Downloads\APEDSK99-APEDSK99_current\Arduino\APEDSK99_012s\APEDSK99_012s-G-AD99cmd.ino:216:9: note: here case 104: //reset current DSR ( ADSR(), ARST() ) ^~~~ In file included from C:\Users\Ricky\Downloads\APEDSK99-APEDSK99_current\Arduino\APEDSK99_012s\APEDSK99_012s.ino:3:0: C:\Users\Ricky\Documents\Arduino\libraries\SdFat\src/FreeStack.h: At global scope: C:\Users\Ricky\Documents\Arduino\libraries\SdFat\src/FreeStack.h:39:12: warning: 'int FreeStack()' defined but not used [-Wunused-function] static int FreeStack() { ^~~~~~~~~ C:\Users\Ricky\Documents\Arduino\libraries\arduino-NTP\src\NTP.cpp: In member function 'bool NTP::begin()': C:\Users\Ricky\Documents\Arduino\libraries\arduino-NTP\src\NTP.cpp:32:1: warning: control reaches end of non-void function [-Wreturn-type] } ^ C:\Users\Ricky\Documents\Arduino\libraries\arduino-FTP\FTP.cpp: In member function 'uint16_t FTP::waitServerCode(char*)': C:\Users\Ricky\Documents\Arduino\libraries\arduino-FTP\FTP.cpp:274:33: warning: invalid conversion from 'char*' to 'uint8_t* {aka unsigned char*}' [-fpermissive] buffLen += cClient.read(buff + buffLen, len); ~~~~~^~~~~~~~~ In file included from C:\Users\Ricky\Documents\Arduino\libraries\arduino-FTP\FTP.h:5:0, from C:\Users\Ricky\Documents\Arduino\libraries\arduino-FTP\FTP.cpp:18: C:\Users\Ricky\AppData\Local\Arduino15\packages\arduino\hardware\avr\1.8.6\cores\arduino/Client.h:35:15: note: initializing argument 1 of 'virtual int Client::read(uint8_t*, size_t)' virtual int read(uint8_t *buf, size_t size) = 0; ^~~~ C:\Users\Ricky\AppData\Local\Arduino15\packages\arduino\hardware\avr\1.8.6\cores\arduino\new.cpp: In function 'void* operator new(std::size_t, std::nothrow_t)': C:\Users\Ricky\AppData\Local\Arduino15\packages\arduino\hardware\avr\1.8.6\cores\arduino\new.cpp:59:60: warning: unused parameter 'tag' [-Wunused-parameter] void * operator new(std::size_t size, const std::nothrow_t tag) noexcept { ^~~ C:\Users\Ricky\AppData\Local\Arduino15\packages\arduino\hardware\avr\1.8.6\cores\arduino\new.cpp: In function 'void* operator new [](std::size_t, const std::nothrow_t&)': C:\Users\Ricky\AppData\Local\Arduino15\packages\arduino\hardware\avr\1.8.6\cores\arduino\new.cpp:68:63: warning: unused parameter 'tag' [-Wunused-parameter] void * operator new[](std::size_t size, const std::nothrow_t& tag) noexcept { ^~~ C:\Users\Ricky\AppData\Local\Arduino15\packages\arduino\hardware\avr\1.8.6\cores\arduino\new.cpp: In function 'void operator delete(void*, const std::nothrow_t&)': C:\Users\Ricky\AppData\Local\Arduino15\packages\arduino\hardware\avr\1.8.6\cores\arduino\new.cpp:103:55: warning: unused parameter 'tag' [-Wunused-parameter] void operator delete(void* ptr, const std::nothrow_t& tag) noexcept { ^~~ C:\Users\Ricky\AppData\Local\Arduino15\packages\arduino\hardware\avr\1.8.6\cores\arduino\new.cpp: In function 'void operator delete [](void*, const std::nothrow_t&)': C:\Users\Ricky\AppData\Local\Arduino15\packages\arduino\hardware\avr\1.8.6\cores\arduino\new.cpp:106:57: warning: unused parameter 'tag' [-Wunused-parameter] void operator delete[](void* ptr, const std::nothrow_t& tag) noexcept { ^~~ Sketch uses 29850 bytes (92%) of program storage space. Maximum is 32256 bytes. Global variables use 1449 bytes (70%) of dynamic memory, leaving 599 bytes for local variables. Maximum is 2048 bytes. An error occurred while uploading the sketch This report would have more information with "Show verbose output during compilation" option enabled in File -> Preferences. "

This turned out to be duplicated due to the 503 error I received

@JJB I am getting this error when trying to compile and program the sketch in the Arduino IDE 1.8.19, what do I need to do to resolve this? What am I missing? "Arduino: 1.8.19 (Windows 10), TD: 1.58, Board: "Arduino Uno" C:\Users\Ricky\Documents\Arduino\sketch_apr21a\APEDSK99_012s-B-HAL.ino: In function 'void disable_controlbus()': APEDSK99_012s-B-HAL:52:3: error: 'pinAsInput' was not declared in this scope pinAsInput(CE); ^~~~~~~~~~ C:\Users\Ricky\Documents\Arduino\sketch_apr21a\APEDSK99_012s-B-HAL.ino: In function 'void enable_controlbus()': APEDSK99_012s-B-HAL:58:3: error: 'pinAsOutput' was not declared in this scope pinAsOutput(CE); ^~~~~~~~~~~ C:\Users\Ricky\Documents\Arduino\sketch_apr21a\APEDSK99_012s-B-HAL.ino: In function 'void set_addressbus(unsigned int)': APEDSK99_012s-B-HAL:79:3: error: 'digitalLow' was not declared in this scope digitalLow(LATCH); //disable latch line ^~~~~~~~~~ C:\Users\Ricky\Documents\Arduino\sketch_apr21a\APEDSK99_012s-B-HAL.ino:79:3: note: suggested alternative: 'digitalRead' digitalLow(LATCH); //disable latch line ^~~~~~~~~~ digitalRead APEDSK99_012s-B-HAL:87:44: error: 'digitalHigh' was not declared in this scope PORTC |= ( (address >> 10) & B00100000); digitalHigh(CLOCK); digitalLow(DS); //A15 ^~~~~~~~~~~ C:\Users\Ricky\Documents\Arduino\sketch_apr21a\APEDSK99_012s-B-HAL.ino:87:44: note: suggested alternative: 'digitalRead' PORTC |= ( (address >> 10) & B00100000); digitalHigh(CLOCK); digitalLow(DS); //A15 ^~~~~~~~~~~ digitalRead C:\Users\Ricky\Documents\Arduino\sketch_apr21a\APEDSK99_012s-B-HAL.ino: In function 'byte read_DSRAM(unsigned int)': APEDSK99_012s-B-HAL:128:3: error: 'digitalLow' was not declared in this scope digitalLow(CE); //enable RAM chip select ^~~~~~~~~~ C:\Users\Ricky\Documents\Arduino\sketch_apr21a\APEDSK99_012s-B-HAL.ino:128:3: note: suggested alternative: 'digitalRead' digitalLow(CE); //enable RAM chip select ^~~~~~~~~~ digitalRead APEDSK99_012s-B-HAL:130:3: error: 'digitalHigh' was not declared in this scope digitalHigh(CE); //disable RAM chip select ^~~~~~~~~~~ C:\Users\Ricky\Documents\Arduino\sketch_apr21a\APEDSK99_012s-B-HAL.ino:130:3: note: suggested alternative: 'digitalRead' digitalHigh(CE); //disable RAM chip select ^~~~~~~~~~~ digitalRead C:\Users\Ricky\Documents\Arduino\sketch_apr21a\APEDSK99_012s-B-HAL.ino: In function 'void write_DSRAM(unsigned int, byte)': APEDSK99_012s-B-HAL:139:3: error: 'digitalLow' was not declared in this scope digitalLow(CE); //enable RAM chip select ^~~~~~~~~~ C:\Users\Ricky\Documents\Arduino\sketch_apr21a\APEDSK99_012s-B-HAL.ino:139:3: note: suggested alternative: 'digitalRead' digitalLow(CE); //enable RAM chip select ^~~~~~~~~~ digitalRead APEDSK99_012s-B-HAL:142:3: error: 'digitalHigh' was not declared in this scope digitalHigh(WE); //disable write ^~~~~~~~~~~ C:\Users\Ricky\Documents\Arduino\sketch_apr21a\APEDSK99_012s-B-HAL.ino:142:3: note: suggested alternative: 'digitalRead' digitalHigh(WE); //disable write ^~~~~~~~~~~ digitalRead C:\Users\Ricky\Documents\Arduino\sketch_apr21a\APEDSK99_012s-B-HAL.ino: In function 'void TIstop()': APEDSK99_012s-B-HAL:152:3: error: 'digitalLow' was not declared in this scope digitalLow(TI_READY); //halts TI and enables 74HC595 shift registers ^~~~~~~~~~ C:\Users\Ricky\Documents\Arduino\sketch_apr21a\APEDSK99_012s-B-HAL.ino:152:3: note: suggested alternative: 'digitalRead' digitalLow(TI_READY); //halts TI and enables 74HC595 shift registers ^~~~~~~~~~ digitalRead APEDSK99_012s-B-HAL:153:3: error: 'digitalHigh' was not declared in this scope digitalHigh(TI_BUFFERS); //disables 74HCT541 address buffers and GAL outputs ^~~~~~~~~~~ C:\Users\Ricky\Documents\Arduino\sketch_apr21a\APEDSK99_012s-B-HAL.ino:153:3: note: suggested alternative: 'digitalRead' digitalHigh(TI_BUFFERS); //disables 74HCT541 address buffers and GAL outputs ^~~~~~~~~~~ digitalRead C:\Users\Ricky\Documents\Arduino\sketch_apr21a\APEDSK99_012s-B-HAL.ino: In function 'void TIgo()': APEDSK99_012s-B-HAL:164:3: error: 'digitalLow' was not declared in this scope digitalLow(TI_BUFFERS); //enables 74HCT541 address buffers and GAL outputs ^~~~~~~~~~ C:\Users\Ricky\Documents\Arduino\sketch_apr21a\APEDSK99_012s-B-HAL.ino:164:3: note: suggested alternative: 'digitalRead' digitalLow(TI_BUFFERS); //enables 74HCT541 address buffers and GAL outputs ^~~~~~~~~~ digitalRead APEDSK99_012s-B-HAL:165:3: error: 'digitalHigh' was not declared in this scope digitalHigh(TI_READY); //disables 74HC595 shift registers and wakes up TI ^~~~~~~~~~~ C:\Users\Ricky\Documents\Arduino\sketch_apr21a\APEDSK99_012s-B-HAL.ino:165:3: note: suggested alternative: 'digitalRead' digitalHigh(TI_READY); //disables 74HC595 shift registers and wakes up TI ^~~~~~~~~~~ digitalRead C:\Users\Ricky\Documents\Arduino\sketch_apr21a\APEDSK99_012s-B-HAL.ino: In function 'void APEDSK99reset()': APEDSK99_012s-B-HAL:170:3: error: 'wdt_disable' was not declared in this scope wdt_disable(); //disable Watchdog (just to be sure) ^~~~~~~~~~~ APEDSK99_012s-B-HAL:171:14: error: 'WDTO_15MS' was not declared in this scope wdt_enable(WDTO_15MS); //enable it and set delay to 15ms ^~~~~~~~~ APEDSK99_012s-B-HAL:171:3: error: 'wdt_enable' was not declared in this scope wdt_enable(WDTO_15MS); //enable it and set delay to 15ms ^~~~~~~~~~ C:\Users\Ricky\Documents\Arduino\sketch_apr21a\APEDSK99_012s-B-HAL.ino:171:3: note: suggested alternative: 'mutable' wdt_enable(WDTO_15MS); //enable it and set delay to 15ms ^~~~~~~~~~ mutable C:\Users\Ricky\Documents\Arduino\sketch_apr21a\APEDSK99_012s-B-HAL.ino: In function 'void Flasher(byte)': APEDSK99_012s-B-HAL:182:3: error: 'digitalHigh' was not declared in this scope digitalHigh(TI_READY); //... but let user enjoy vanilla console ^~~~~~~~~~~ C:\Users\Ricky\Documents\Arduino\sketch_apr21a\APEDSK99_012s-B-HAL.ino:182:3: note: suggested alternative: 'digitalRead' digitalHigh(TI_READY); //... but let user enjoy vanilla console ^~~~~~~~~~~ digitalRead APEDSK99_012s-B-HAL:186:7: error: 'digitalLow' was not declared in this scope digitalLow(CE); //set RAM CE* LOW, turns on LED ^~~~~~~~~~ C:\Users\Ricky\Documents\Arduino\sketch_apr21a\APEDSK99_012s-B-HAL.ino:186:7: note: suggested alternative: 'digitalRead' digitalLow(CE); //set RAM CE* LOW, turns on LED ^~~~~~~~~~ digitalRead C:\Users\Ricky\Documents\Arduino\sketch_apr21a\APEDSK99_012s-C-global_suppfnc.ino: In function 'void EtherStart()': APEDSK99_012s-C-global_suppfnc:54:16: error: 'ETH_CS' was not declared in this scope pinAsOutput( ETH_CS ); //enable EthernetShield CS (shared with TI_INT) ^~~~~~ APEDSK99_012s-C-global_suppfnc:54:3: error: 'pinAsOutput' was not declared in this scope pinAsOutput( ETH_CS ); //enable EthernetShield CS (shared with TI_INT) ^~~~~~~~~~~ APEDSK99_012s-C-global_suppfnc:56:19: error: 'MAC' was not declared in this scope Ethernet.begin( MAC, ACFG.ipaddress ); //... with set MAC address and IP address ^~~ C:\Users\Ricky\Documents\Arduino\sketch_apr21a\APEDSK99_012s-C-global_suppfnc.ino: In function 'void EtherStop()': APEDSK99_012s-C-global_suppfnc:60:3: error: 'client' was not declared in this scope client.stop(); //stop Ethernet client ^~~~~~ C:\Users\Ricky\Documents\Arduino\sketch_apr21a\APEDSK99_012s-C-global_suppfnc.ino:60:3: note: suggested alternative: 'Client' client.stop(); //stop Ethernet client ^~~~~~ Client APEDSK99_012s-C-global_suppfnc:61:3: error: 'pinAsInput' was not declared in this scope pinAsInput(TI_INT); //disable EthernetShield SS / enable TI_INT ^~~~~~~~~~ C:\Users\Ricky\Documents\Arduino\sketch_apr21a\APEDSK99_012s-C-global_suppfnc.ino: In function 'boolean prepDSK()': APEDSK99_012s-C-global_suppfnc:106:23: error: 'SD' was not declared in this scope boolean existDOAD = SD.exists( DOADfullpath ); ^~ C:\Users\Ricky\Documents\Arduino\sketch_apr21a\APEDSK99_012s-C-global_suppfnc.ino:106:23: note: suggested alternative: 'SDA' boolean existDOAD = SD.exists( DOADfullpath ); ^~ SDA C:\Users\Ricky\Documents\Arduino\sketch_apr21a\APEDSK99_012s-C-global_suppfnc.ino: In function 'void CALLstatus(byte)': APEDSK99_012s-C-global_suppfnc:129:12: error: 'SD' was not declared in this scope DSKx = SD.open( "/CALLerr.txt", FILE_READ ); //open error text file ^~ C:\Users\Ricky\Documents\Arduino\sketch_apr21a\APEDSK99_012s-C-global_suppfnc.ino:129:12: note: suggested alternative: 'SDA' DSKx = SD.open( "/CALLerr.txt", FILE_READ ); //open error text file ^~ SDA C:\Users\Ricky\Documents\Arduino\sketch_apr21a\APEDSK99_012s-C-global_suppfnc.ino: In function 'byte getNTPdt()': APEDSK99_012s-C-global_suppfnc:157:3: error: 'ntp' was not declared in this scope ntp.begin(); //start NTP client ^~~ C:\Users\Ricky\Documents\Arduino\sketch_apr21a\APEDSK99_012s-E-init.ino: In function 'void setup()': APEDSK99_012s-E-init:1:6: error: redefinition of 'void setup()' void setup() { ^~~~~ C:\Users\Ricky\Documents\Arduino\sketch_apr21a\sketch_apr21a.ino:19:6: note: 'void setup()' previously defined here void setup() { ^~~~~ APEDSK99_012s-E-init:3:3: error: 'pinAsOutput' was not declared in this scope pinAsOutput(TI_BUFFERS); //enable* or disable 74HCT541 address buffers and GAL outputs ^~~~~~~~~~~ APEDSK99_012s-E-init:8:15: error: 'ETHSD_SS' was not declared in this scope pinAsOutput(ETHSD_SS); //initialise shield SS pin ^~~~~~~~ APEDSK99_012s-E-init:9:3: error: 'digitalHigh' was not declared in this scope digitalHigh(ETHSD_SS); //without this SPI subsystem won't work ^~~~~~~~~~~ C:\Users\Ricky\Documents\Arduino\sketch_apr21a\APEDSK99_012s-E-init.ino:9:3: note: suggested alternative: 'digitalRead' digitalHigh(ETHSD_SS); //without this SPI subsystem won't work ^~~~~~~~~~~ digitalRead APEDSK99_012s-E-init:11:9: error: 'SD' was not declared in this scope if ( !SD.begin(SPI_CS) ) { //SD card present and can be initialized? ^~ C:\Users\Ricky\Documents\Arduino\sketch_apr21a\APEDSK99_012s-E-init.ino:11:9: note: suggested alternative: 'SDA' if ( !SD.begin(SPI_CS) ) { //SD card present and can be initialized? ^~ SDA APEDSK99_012s-E-init:11:18: error: 'SPI_CS' was not declared in this scope if ( !SD.begin(SPI_CS) ) { //SD card present and can be initialized? ^~~~~~ C:\Users\Ricky\Documents\Arduino\sketch_apr21a\APEDSK99_012s-E-init.ino:11:18: note: suggested alternative: 'SPI' if ( !SD.begin(SPI_CS) ) { //SD card present and can be initialized? ^~~~~~ SPI APEDSK99_012s-E-init:21:8: error: 'EEPROM' was not declared in this scope if ( EEPROM.read(EEPROM_DSR) == 0xFF ) { //invalid DSR (i.e. virgin Uno EEPROM or invalid DSR filename)? ^~~~~~ C:\Users\Ricky\Documents\Arduino\sketch_apr21a\APEDSK99_012s-E-init.ino:21:8: note: suggested alternative: 'EEPROM_h' if ( EEPROM.read(EEPROM_DSR) == 0xFF ) { //invalid DSR (i.e. virgin Uno EEPROM or invalid DSR filename)? ^~~~~~ EEPROM_h APEDSK99_012s-E-init:25:3: error: 'EEPROM' was not declared in this scope EEPROM.get( EEPROM_DSR, DSRtoload ); //get DSR filename from EEPROM ^~~~~~ C:\Users\Ricky\Documents\Arduino\sketch_apr21a\APEDSK99_012s-E-init.ino:25:3: note: suggested alternative: 'EEPROM_h' EEPROM.get( EEPROM_DSR, DSRtoload ); //get DSR filename from EEPROM ^~~~~~ EEPROM_h APEDSK99_012s-E-init:26:8: error: 'SD' was not declared in this scope if ( SD.exists(DSRtoload) ) { //does it exist? ... ^~ C:\Users\Ricky\Documents\Arduino\sketch_apr21a\APEDSK99_012s-E-init.ino:26:8: note: suggested alternative: 'SDA' if ( SD.exists(DSRtoload) ) { //does it exist? ... ^~ SDA APEDSK99_012s-E-init:44:10: error: 'SD' was not declared in this scope if ( SD.exists( nameDSK[ii] ) ) { //does DOAD exist? ^~ C:\Users\Ricky\Documents\Arduino\sketch_apr21a\APEDSK99_012s-E-init.ino:44:10: note: suggested alternative: 'SDA' if ( SD.exists( nameDSK[ii] ) ) { //does DOAD exist? ^~ SDA APEDSK99_012s-E-init:64:3: error: 'pinAsInputPullUp' was not declared in this scope pinAsInputPullUp(TI_INT); //from Ethernet SS to detecting TI Interrupts ^~~~~~~~~~~~~~~~ C:\Users\Ricky\Documents\Arduino\sketch_apr21a\APEDSK99_012s-F-FD1771cmd.ino: In function 'void loop()': APEDSK99_012s-F-FD1771cmd:1:6: error: redefinition of 'void loop()' void loop() { ^~~~ C:\Users\Ricky\Documents\Arduino\sketch_apr21a\sketch_apr21a.ino:24:6: note: 'void loop()' previously defined here void loop() { ^~~~ APEDSK99_012s-F-FD1771cmd:8:11: error: 'isHigh' was not declared in this scope while ( isHigh(TI_INT) ) { //... concentrate on GAL "write to DSR RAM" signal ^~~~~~ C:\Users\Ricky\Documents\Arduino\sketch_apr21a\APEDSK99_012s-F-FD1771cmd.ino:8:11: note: suggested alternative: 'isDigit' while ( isHigh(TI_INT) ) { //... concentrate on GAL "write to DSR RAM" signal ^~~~~~ isDigit APEDSK99_012s-F-FD1771cmd:27:16: error: 'SD' was not declared in this scope DSKx = SD.open( nameDSK[currentDSK], FILE_WRITE ); //open SD DOAD file ^~ C:\Users\Ricky\Documents\Arduino\sketch_apr21a\APEDSK99_012s-F-FD1771cmd.ino:27:16: note: suggested alternative: 'SDA' DSKx = SD.open( nameDSK[currentDSK], FILE_WRITE ); //open SD DOAD file ^~ SDA APEDSK99_012s-G-AD99cmd:22:20: error: 'SD' was not declared in this scope DSKx = SD.open( nameDSK[currentDSK], FILE_WRITE); //open DOAD file to change write protect status ^~ C:\Users\Ricky\Documents\Arduino\sketch_apr21a\APEDSK99_012s-G-AD99cmd.ino:22:20: note: suggested alternative: 'SDA' DSKx = SD.open( nameDSK[currentDSK], FILE_WRITE); //open DOAD file to change write protect status ^~ SDA APEDSK99_012s-G-AD99cmd:37:22: error: 'SD' was not declared in this scope DSKx = SD.open( nameDSK[currentDSK], FILE_READ ); //yes; prep DOAD ^~ C:\Users\Ricky\Documents\Arduino\sketch_apr21a\APEDSK99_012s-G-AD99cmd.ino:37:22: note: suggested alternative: 'SDA' DSKx = SD.open( nameDSK[currentDSK], FILE_READ ); //yes; prep DOAD ^~ SDA APEDSK99_012s-G-AD99cmd:113:24: error: 'SD' was not declared in this scope DSKx = SD.open( nameDSK[currentDSK], FILE_WRITE ); //yes; safe to rename ^~ C:\Users\Ricky\Documents\Arduino\sketch_apr21a\APEDSK99_012s-G-AD99cmd.ino:113:24: note: suggested alternative: 'SDA' DSKx = SD.open( nameDSK[currentDSK], FILE_WRITE ); //yes; safe to rename ^~ SDA APEDSK99_012s-G-AD99cmd:149:15: error: 'SD' was not declared in this scope SD.remove( DOADfullpath ); //yes; delete DOAD from SD card ^~ C:\Users\Ricky\Documents\Arduino\sketch_apr21a\APEDSK99_012s-G-AD99cmd.ino:149:15: note: suggested alternative: 'SDA' SD.remove( DOADfullpath ); //yes; delete DOAD from SD card ^~ SDA APEDSK99_012s-G-AD99cmd:165:17: error: 'ftp' was not declared in this scope if ( !ftp.connect(ACFG.ftpserver, ACFG.ftpuser, ACFG.ftpass) ) { //if we can't connect to FTP server ... ^~~ APEDSK99_012s-G-AD99cmd:175:15: error: 'ftp' was not declared in this scope ftp.store( DOADfilename, DSKx ); //send DOAD to ftp server ^~~ APEDSK99_012s-G-AD99cmd:184:22: error: 'SD' was not declared in this scope DSKx = SD.open( "/_FT", FILE_WRITE ); //... as we are opening a temporary FTP file ^~ C:\Users\Ricky\Documents\Arduino\sketch_apr21a\APEDSK99_012s-G-AD99cmd.ino:184:22: note: suggested alternative: 'SDA' DSKx = SD.open( "/_FT", FILE_WRITE ); //... as we are opening a temporary FTP file ^~ SDA APEDSK99_012s-G-AD99cmd:185:15: error: 'ftp' was not declared in this scope ftp.retrieve( DOADfilename, DSKx ); //get DOAD from FTP server ^~~ APEDSK99_012s-G-AD99cmd:206:16: error: 'SD' was not declared in this scope if ( SD.exists(DOADfilename) ) { //does new DSR exist? ^~ C:\Users\Ricky\Documents\Arduino\sketch_apr21a\APEDSK99_012s-G-AD99cmd.ino:206:16: note: suggested alternative: 'SDA' if ( SD.exists(DOADfilename) ) { //does new DSR exist? ^~ SDA APEDSK99_012s-G-AD99cmd:207:13: error: 'EEPROM' was not declared in this scope EEPROM.put( EEPROM_DSR, DOADfilename ); //yes; update DSR info in EEPROM ... ^~~~~~ C:\Users\Ricky\Documents\Arduino\sketch_apr21a\APEDSK99_012s-G-AD99cmd.ino:207:13: note: suggested alternative: 'EEPROM_h' EEPROM.put( EEPROM_DSR, DOADfilename ); //yes; update DSR info in EEPROM ... ^~~~~~ EEPROM_h APEDSK99_012s-G-AD99cmd:240:16: error: 'SD' was not declared in this scope if ( SD.exists( DOADfilename ) ) { //does folder exist? ... ^~ C:\Users\Ricky\Documents\Arduino\sketch_apr21a\APEDSK99_012s-G-AD99cmd.ino:240:16: note: suggested alternative: 'SDA' if ( SD.exists( DOADfilename ) ) { //does folder exist? ... ^~ SDA APEDSK99_012s-G-AD99cmd:268:24: error: 'SD' was not declared in this scope DSKx = SD.open( nameDSK[currentDSK], FILE_READ ); //open DOAD ^~ C:\Users\Ricky\Documents\Arduino\sketch_apr21a\APEDSK99_012s-G-AD99cmd.ino:268:24: note: suggested alternative: 'SDA' DSKx = SD.open( nameDSK[currentDSK], FILE_READ ); //open DOAD ^~ SDA APEDSK99_012s-G-AD99cmd:322:23: error: 'SD' was not declared in this scope SDdir = SD.open( "/" ); //... openening root folder ^~ C:\Users\Ricky\Documents\Arduino\sketch_apr21a\APEDSK99_012s-G-AD99cmd.ino:322:23: note: suggested alternative: 'SDA' SDdir = SD.open( "/" ); //... openening root folder ^~ SDA APEDSK99_012s-G-AD99cmd:362:21: error: 'SD' was not declared in this scope SDdir = SD.open( DSKfolder ); //yes; open directory ^~ C:\Users\Ricky\Documents\Arduino\sketch_apr21a\APEDSK99_012s-G-AD99cmd.ino:362:21: note: suggested alternative: 'SDA' SDdir = SD.open( DSKfolder ); //yes; open directory ^~ SDA APEDSK99_012s-G-AD99cmd:399:20: error: 'SD' was not declared in this scope DSKx = SD.open( "/CALLhlp.txt", FILE_READ ); //first run, open help file ^~ C:\Users\Ricky\Documents\Arduino\sketch_apr21a\APEDSK99_012s-G-AD99cmd.ino:399:20: note: suggested alternative: 'SDA' DSKx = SD.open( "/CALLhlp.txt", FILE_READ ); //first run, open help file ^~ SDA APEDSK99_012s-G-AD99cmd:416:20: error: 'SD' was not declared in this scope DSKx = SD.open( "/tilcchar.bin", FILE_READ ); //first run, open definition file ^~ C:\Users\Ricky\Documents\Arduino\sketch_apr21a\APEDSK99_012s-G-AD99cmd.ino:416:20: note: suggested alternative: 'SDA' DSKx = SD.open( "/tilcchar.bin", FILE_READ ); //first run, open definition file ^~ SDA APEDSK99_012s-G-AD99cmd:445:22: error: 'SD' was not declared in this scope DSKx = SD.open( nameDSK[currentDSK], FILE_WRITE ); ^~ C:\Users\Ricky\Documents\Arduino\sketch_apr21a\APEDSK99_012s-G-AD99cmd.ino:445:22: note: suggested alternative: 'SDA' DSKx = SD.open( nameDSK[currentDSK], FILE_WRITE ); ^~ SDA APEDSK99_012s-G-AD99cmd:457:18: error: 'SD' was not declared in this scope DSKx = SD.open( nameDSK[0], FILE_READ ); //expect ACFG.DSK mapped to DSK1 ^~ C:\Users\Ricky\Documents\Arduino\sketch_apr21a\APEDSK99_012s-G-AD99cmd.ino:457:18: note: suggested alternative: 'SDA' DSKx = SD.open( nameDSK[0], FILE_READ ); //expect ACFG.DSK mapped to DSK1 ^~ SDA APEDSK99_012s-G-AD99cmd:506:11: error: 'EEPROM' was not declared in this scope EEPROM.put( EEPROM_CFG, ACFG ); //save configuration struct to EEPROM ^~~~~~ C:\Users\Ricky\Documents\Arduino\sketch_apr21a\APEDSK99_012s-G-AD99cmd.ino:506:11: note: suggested alternative: 'EEPROM_h' EEPROM.put( EEPROM_CFG, ACFG ); //save configuration struct to EEPROM ^~~~~~ EEPROM_h exit status 1 'pinAsInput' was not declared in this scope This report would have more information with "Show verbose output during compilation" option enabled in File -> Preferences. "

Yep the same would got for the CF7+. I have two both the have the 32k and He sent me a CPLD that would work with the 32k not installed, but installed it wouldn't work. The other I don't know if it still works or not, think the CF card was messed up, by one of my grandchildren.

I'd think that they're all, worth archiving, if they aren't know to be in the WHTECH repository or other accessible places. The Latin disk is one I haven't seen as well as others.

Go into windows defender and to the quarantine link then under actions allow it. Unless you don't trust it.